Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Heat exchangers construction materials

Increased corrosion of reactor and heat exchanger construction materials. [Pg.435]

The reactor products are so hot or corrosive that if passed directly to a heat exchanger, special materials-of-construction or an expensive mechanical design would be required. [Pg.43]

The rupture tests revealed that the burst strength of all of the tubes was not diminished by the environmental conditions. All of the materials which were tested appeared to be satisfactory, but type 316L stainless steel was chosen as the best construction material because its welding, forming, and brazing characteristics were found to be more suitable for the heat exchanger construction. [Pg.246]

Hall, S. G., Ahmad, S., and Smith, R., Capital Cost Target for Heat Exchanger Networks Comprising Mixed Materials of Construction, Pressure Ratings and Exchanger Types, Computers Chem. Eng., 14 319, 1990. [Pg.237]

In order to maintain high energy efficiency and ensure a long service life of the materials of construction in the combustion chamber, turbine and jet nozzle, a clean burning flame must be obtained that minimizes the heat exchange by radiation and limits the formation of carbon deposits. These qualities are determined by two procedures that determine respectively the smoke point and the luminometer index. [Pg.226]

Fixed-Tube-Sheet Heat Exchang ers Fixed-tube-sheet exchangers (Fig. 11-36Z ) are used more often than any other type, and the frequency of use has been increasing in recent years. The tube sheets are welded to the shell. Usually these extend beyond the shell and serve as flanges to which the tube-side headers are bolted. This construction requires that the shell and tube-sheet materials be weldable to each other. [Pg.1066]

Some of the special considerations in regard to heat-exchanger corrosion are discussed in this subsection. A more extended presentation in Sec. 23 covers corrosion and its various forms as well as materials of construction. [Pg.1073]

Materials of Construction The most common material of construction for heat exchangers is carbon steel. Stainless-steel construction throughout is sometimes used in chemical-plant service and on rare occasions in petroleum refining. Many exchangers are constructed from dissimilar metals. Such combinations are functioning satisfactorily in certain sei vices. Extreme care in their selection is required since electrolytic attack can develop. [Pg.1073]

The price of air-cooled exchangers should be obtained from vendors if possible. If not, then by coirelating in-house historical data on a basis of /ft of bare surface vs. total bare surface. Correction factors for materials of construction. pressure, numbers of tube rows, and tube length must be used. Literature data on air coolers is available (Reference 15). but it should be the last resort. In any event, at least one air-cooled heat exchanger in each project should be priced by a vendor to calibrate the historical data to reflect the supply and demand situation at the expected time of procurement. [Pg.233]

Cone roof and floating roof tanks are usually correlated using vs. volume, w ith materials of construction as another variable. The cost of internal heat exchangers, insulation, unusual corrosion allowance, and special internals should be separated from the basic cost of the tank in the correlations. [Pg.233]

Pressure storage tanks should be coirelated using /lb vs. w eight, much the same as other pressure vessels. Materials of construction, of course, would be another variable. Special internals, insulation, and internal heat exchangers should again be separated from the base cost of the tank. The w eight of supports, ladders, and platforms should be estimated and added to the weight of the... [Pg.233]

Common to all air cooled heat exchangers is the tube, through which the process fluid flows. To compensate for the poor heat transfer properties of air, which flows across the outside of the tube, and to reduce the overall dimensions of the heat exchanger, external fins are added to the outside of the tube. A wide variety of finned tube types are available for use in air cooled exchangers. These vary in geometry, materials, and methods of construction, which affect both air side thermal performance and air side pressure drop. In addition, particular... [Pg.12]

In order to illustrate the use of cost indices and scaling factors, let us consider the following example. In 1992, the cost of a 50 m shell-and-tube beat exchanger was 24,000. Estimate the cost of a 100 m shell-and-tube heat exchanger of a similar type and materials of construction in 1996. [Pg.304]

Process flow diagrams are more complex and show all main flow streams including valves to enhance the understanding of the process as well as pressures and temperatures on all feed and product lines within all major vessels and in and out of headers and heat exchangers, and points of pressure and temperature control. Also, information on construction materials, pump capacities and pressure heads, compressor horsepower, and vessel design pressures and temperatures are shown when necessary for clarity. In addition, process flow diagrams usually show major components of control loops along with key utilities. [Pg.230]

The factors that affect the evaporation process are concentration in the liquid, solubility, pressure, temperature, scaling, and materials of construction. An evaporator is a type of heat exchanger designed to induce boiling and evaporation of a liquid. The major types of evaporator are... [Pg.140]

Natural and forced-draft cooling towers are generally used to provide the cooling water required on a site, unless water can be drawn from a convenient river or lake in sufficient quantity. Seawater or brackish water can be used at coastal sites, but if used directly will necessitate more expensive materials of construction for heat exchangers. [Pg.156]

Cowan, C. T, Choosing Materials of Construction for Plate Heat Exchangers, Chem. ng ,June 9 (1975) p. 100. [Pg.286]

Simple heat exchangers. These can be of the parallel flow, cross-flow or counter-flow pattern and constructed of materials to suit the temperature. [Pg.267]

Economizer. The economizer is a tubular heat exchanger used to recover heat from the exhaust gases from boilers or some processes. It is used in boilers to recover much of the sensible heat for use in preheating the boiler feedwater. An increase in boiler efficiency of 4-6 per cent is typical. The design and materials of construction depend on the application. [Pg.267]

Atomic power production The necessity for avoiding contamination of operative liquids, together with other requirements which must be met in selecting constructional materials in this highly specialised field has resulted in the choice of austenitic steels for applications in heat exchangers, pressure vessels, pipelines and fuel processing. [Pg.560]


See other pages where Heat exchangers construction materials is mentioned: [Pg.117]    [Pg.174]    [Pg.117]    [Pg.174]    [Pg.1051]    [Pg.495]    [Pg.70]    [Pg.172]    [Pg.525]    [Pg.97]    [Pg.98]    [Pg.1387]    [Pg.1080]    [Pg.77]    [Pg.580]    [Pg.387]    [Pg.229]    [Pg.232]    [Pg.396]    [Pg.401]    [Pg.471]    [Pg.1219]    [Pg.2421]    [Pg.36]    [Pg.25]    [Pg.36]    [Pg.274]    [Pg.708]    [Pg.8]    [Pg.267]    [Pg.315]   


SEARCH



Construction materials

Constructional materials

Heat exchangers construction

Heating Materials

© 2024 chempedia.info