Ground cellulose

For a natural substrate like ground cellulose or fruit pulp, of order... 

Following Permea s success, several companies produced membrane systems to treat natural gas streams, particularly to separate carbon dioxide from methane. The goal is to produce a stream containing less than 2% carbon dioxide to be sent to the national pipeline and a permeate enriched in carbon dioxide to be flared or reinjected into the ground. Cellulose acetate is the most widely used membrane material for this separation, but because its carbon dioxide/methane selectivity is only about 15, two-stage systems are often required to achieve a sufficient separation. The membrane process is generally best suited to relatively small streams, but the economics have slowly improved over the years and more... 

Although it would be desirable to recycle laminate scrap, this has been difficult because of its thermoset nature. However, a 1993 patent (18) suggested a means whereby scrap consisting of cellulose, thermoset resins, and partially reacted resins can be ground to a powder which is used as a filler in a thermoplastic resin. The filled thermoplastic resin is then used for mol ding of various articles. 

The lambda type is nongelling, and functions as a thickner. Iota-carrageenan has been recommended (45) for use in formulating low fat ground beef due to its abihty to retain moisture, especially through a freeze—thaw cycle which is typical for ground beef patties. Oat bran and oat fiber can also be used to improve moisture retention and mouth feel. Modified starches can be used as binders to maintain juiciness and tenderness in low fat meat products. Maltodextrins (dextrose equivalent less than 20) may be used as binders up to 3.5% in finished meat products. Other carbohydrates such as konjac flour, alginate, microcrystalline cellulose, methylceUulose, and carboxymethylceUulose have also been used in low fat meat products (see CELLULOSE ETHERs). 

Filter aids should have low bulk density to minimize settling and aid good distribution on a filter-medium surface that may not be horizontal. They should also be porous and capable of forming a porous cake to minimize flow resistance, and they must be chemically inert to the filtrate. These characteristics are all found in the two most popular commercial filter aids diatomaceous silica (also called diatomite, or diatomaceous earth), which is an almost pure silica prepared from deposits of diatom skeletons and expanded perhte, particles of puffed lava that are principally aluminum alkali siheate. Cellulosic fibers (ground wood pulp) are sometimes used when siliceous materials cannot be used but are much more compressible. The use of other less effective aids (e.g., carbon and gypsum) may be justified in special cases. Sometimes a combination or carbon and diatomaceous silica permits adsorption in addition to filter-aid performance. Various other materials, such as salt, fine sand, starch, and precipitated calcium carbonate, are employed in specific industries where they represent either waste material or inexpensive alternatives to conventional filter aids. 

PPVC has also retained a substantial market as a leathercloth, where it is more durable than earlier cellulose-based products. In the 1950s and 1960s it largely replaced leather as a car upholstery material on grounds of cost and durability but was never very popular with consumers. As a result, since the 1970s it has been largely replaced by various fabric materials which have, to this writer at least, proved very durable and preferable in terms of comfort. 

Cellulosic materials, such as wood, in their different forms (i.e., wood flour and wood pulp), cotton, shell flours, ground com cobs, and other vegetable by-products or agro-wastes are used as the source of cellulosic raw materials for the plastic industry [29,56], at least as... 

Dried shrimp was ground, defatted with benzene, and then extracted with cold water. The luciferase extracted was purified first by a batch adsorption onto DEAE cellulose (elution with 0.4 M NaCl), followed by gel filtration on a column of Sephadex G-150, anion-exchange chromatography on a column of DEAE-cellulose (gradient elution 0.05-0.5 M NaCl), and gel filtration on a column of Ultrogel AcA 34. The specific activity of the purified luciferase was 1.7 x 1015 photons s 1 mg-1, and the yield in terms of luciferase activity was about 28%. 

Representative condensation polymers are listed in Table I. The list is by no means exhaustive, but it serves to indicate the variety of condensation reactions which may be employed in the synthesis of polymers. Cellulose and proteins, although their syntheses have not been accomplished by condensation polymerization in the laboratory, nevertheless are included within the definition of condensation polymers on the ground that they can be degraded, hydrolytically, to monomers differing from the structural units by the addition of the elements of a molecule of water. This is denoted by the direction of the arrows in the table, indicating depolymerization. 

Vertical surfaces collect spray primarily by impaction. Plants and other entities with a vertical component will collect some material by impaction, and typically also by deposition, as discussed in the previous section. While horizontal collectors will tend to collect all or most material that falls out on to them, vertical collectors will have collection efficiencies that are more closely related to their physical characteristics, especially collector diameter. The SDTF used a-cellulose cards oriented perpendicular to the ground and strings made of cotton or Teflon in its field studies to assess spray volumes at locations above the ground. Many other researchers have used strings for assessing airborne spray volumes in drift studies. ... 

Weigh a finely ground representative crop sample (20 g for grain or 10 g for straw) into a cellulose extraction thimble. Assemble a Soxhlet extractor using a 500-mL round-bottom flask containing 200 mL of acetone and boiling chips. Place the extraction... 

---