Glass transition temperatures groups

In addition to thermodynamic appUcations, 62 values have also been related to the glass transition temperature of a polymer, and the difference 62-61 to the viscosity of polymer solutions. The best values of 6 have been analyzed into group contributions, the sum of which can be used to estimate 62 for polymers which have not been characterized experimentally. 

In methacrylic ester polymers, the glass-transition temperature, is influenced primarily by the nature of the alcohol group as can be seen in Table 1. Below the the polymers are hard, brittle, and glass-like above the they are relatively soft, flexible, and mbbery. At even higher temperatures, depending on molecular weight, they flow and are tacky. Table 1 also contains typical values for the density, solubiHty parameter, and refractive index for various methacrylic homopolymers. 

The iatroduction of a plasticizer, which is a molecule of lower molecular weight than the resia, has the abiUty to impart a greater free volume per volume of material because there is an iucrease iu the proportion of end groups and the plasticizer has a glass-transition temperature, T, lower than that of the resia itself A detailed mathematical treatment (2) of this phenomenon can be carried out to explain the success of some plasticizers and the failure of others. Clearly, the use of a given plasticizer iu a certain appHcation is a compromise between the above ideas and physical properties such as volatiUty, compatibihty, high and low temperature performance, viscosity, etc. This choice is appHcation dependent, ie, there is no ideal plasticizer for every appHcation. 

Polar groups, eg, carbonyl and sulfonyl, that are capable of conjugation with the aromatic ring increase the glass-transition temperature, eg, to 245°C for the sulfonyl group, as in (5). 

Carbon Cha.in Backbone Polymers. These polymers may be represented by (4) and considered derivatives of polyethylene, where n is the degree of polymeriza tion and R is (an alkyl group or) a functional group hydrogen (polyethylene), methyl (polypropylene), carboxyl (poly(acryhc acid)), chlorine (poly(vinyl chloride)), phenyl (polystyrene) hydroxyl (poly(vinyl alcohol)), ester (poly(vinyl acetate)), nitrile (polyacrylonitrile), vinyl (polybutadiene), etc. The functional groups and the molecular weight of the polymers, control thek properties which vary in hydrophobicity, solubiUty characteristics, glass-transition temperature, and crystallinity. 

There are a number of structural features which have a bearing on the value of the glass transition temperature. Since this temperature is that at which molecular rotation about single bonds becomes restricted, it is obvious that these features are ones which influence the ease of rotation. These can be divided into two groups ... 

When dipoles are directly attached to the chain their movement will obviously depend on the ability of chain segments to move. Thus the dipole polarisation effect will be much less below the glass transition temperature, than above it Figure 6.4). For this reason unplasticised PVC, poly(ethylene terephthalate) and the bis-phenol A polycarbonates are better high-frequency insulators at room temperature, which is below the glass temperature of each of these polymers, than would be expected in polymers of similar polarity but with the polar groups in the side chains. 

Whilst the Tg of poly(dimethylsiloxane) rubbers is reported to be as low as -123°C they do become stiff at about -60 to -80°C due to some crystallisation. Copolymerisation of the dimethyl intermediate with a small amount of a dichlorodiphenylsilane or, preferably, phenylmethyldichlorosilane, leads to an irregular structure and hence amorphous polymer which thus remains a rubber down to its Tg. Although this is higher than the Tg of the dimethylsiloxane it is lower than the so that the polymer remains rubbery down to a lower temperature (in some cases down to -100°C). The Tg does, however, increase steadily with the fraction of phenylsiloxane and eventually rises above that of the of the dimethylsilicone rubber. In practice the use of about 10% of phenyldichlorosilane is sufficient to inhibit crystallisation without causing an excess rise in the glass transition temperature. As with the polydimethylsilox-anes, most methylphenyl silicone rubbers also contain a small amount of vinyl groups. 

As shown in Table 3, the glass transition temperature of the acrylate homopolymers is very much dependent on the nature of the alcohol that was used to make the acrylate ester. Typically, the Tg is the lowest when the number of carbons in the alkyl group (R in the formula above) is about 8-12. 

---