Galvanic cells compared with electrolytic

An electrochemical cell diagram is conventionally arranged in such a way that electrons flow from left to right in the equation. Comparing this with eqn. (6.30), we obtain the following sign convention for a galvanic cell and an electrolytic cell, respectively. 

A parameter that is convenient for said purpose is the electrode potential E it must not be confused with the concept of a potential difference between the electrode and the electrolyte. By convention the term electrode potential E is used to denote the OCV of a galvanic cell that consists of the given electrode (the one that is studied) and a reference electrode selected arbitrarily. Thus, the potential of this electrode is compared with that of a reference electrode that is identical for all electrodes being studied. In accordance with this dehnition, the electrode potential of the reference electrode itself is (conventionally) regarded as zero. Any electrode system for which the equilibrium Galvani potential is established sufficiently rapidly and reproducibly can be used as a reference electrode. We shall write the electrode system to be used as the reference electrode, generally, as M /E ... 

In this section, you learned about electrolytic cells, which convert electrical energy into chemical energy. You compared the spontaneous reactions in galvanic cells, which have positive cell potentials, with the non-spontaneous reactions in electrolytic cells, which have negative cell potentials. You then considered cells that act as both galvanic cells and electrolytic cells in some common rechargeable batteries. These batteries are an important application of electrochemistry. In the next two sections, you will learn about many more electrochemical applications. 

A solid state galvanic cell consists of electrodes and the electrolyte. Solid electrolytes are available for many different mobile ions (see Section 15.3). Their ionic conductivities compare with those of liquid electrolytes (see Fig. 15-8). Under load, galvanic cells transport a known amount of component from one electrode to the other. Therefore, we can predetermine the kinetic boundary condition for transport into a solid (i.e., the electrode). By using a reference electrode we can simultaneously determine the component activity. The combination of component transfer and potential determination is called coulometric titration. It is a most useful method for the thermodynamic and kinetic investigation of compounds with narrow homogeneity ranges. For example, it has been possible to measure in a... 

Electrolytic cell An electrochemical cell that requires an external source of energy to drive the cell reaction. Compare with galvanic cell. 

In principle the activity coefficients yb of solute substances B in a solution can be directly determined from the results of measurements at ven temperature of the pressure and the compositions of the liquid (or solid) solution and of the coexisting gas phase. In practice, this method fails unless the solutes have volatilities comparable with that of the solvent. The method therefore usually fails for electrolyte solutions, for which measurements of ye in practice, much more important than for nonelectrolyte solutions. Three practical methods are available. If the osmotic coefficient of the solvent has been measured over a sufficient range of molalities, the activity coefficients /b can be calculated the method is outlined below under the sub-heading Solvent. The ratio yj/ys of the activity coefficients of a solute B in two solutions, each saturated with respect to solid B in the same solvent but with different molalities of other solutes, is equal to the ratio m lm of the molalities (solubilities expressed as molalities) of B in the saturated solutions. If a justifiable extrapolation to Ssms 0 can be made, then the separate ys s can be found. The method is especially useful when B is a sparingly soluble salt and the solubility is measured in the presence of varying molalities of other more soluble salts. Finally, the activity coefficient of an electrolyte can sometimes be obtained from e.m.f. measurements on galvanic cells. The measurement of activity coefficients and analysis of the results both for solutions of a single electrolyte and for solutions of two or more electrolytes will be dealt with in a subsequent volume. Unfortunately, few activity coefficients have been measured in the usually multi-solute solutions relevant to chemical reactions in solution. 

Galvanic corrosion (also called "dissimilar metal corrosion" or wrongly "electrolysis") refers to corrosion damage induced when two dissimilar materials are coupled in a corrosive electrolyte. In a bimetallic couple, the less noble material becomes the anode and tends to corrode at an accelerated rate, compared with the uncoupled condition and the more noble material will act as the cathode in the corrosion cell. 

Since the 1980 s, a new type of humidity sensor, based on a solid electrolyte, has been under development. The sensor uses a protonic conductor as a base component and makes a galvanic cell of a water vapor gas concentration type. When the characteristics of this new type of sensor are compared with conventional humidity sensors, two representative advantages of this sensor are seen. The sensor output is an EMF change, and is suitable for continuous operation with a fast response. The sensor can operate at higher temperatures, because the solid electrolyte is stable even at elevated temperatures. These features are expected to accelerate the development of this type of sensor. The base material is a perovskite-type strontium cerate SrCeOa. The pure cerate is not a protonic conductor. 

---