Enthalpy standard state thermal properties

The standard state for a pure liquid or solid is taken to be the substance in that state of aggregation at a pressure of 1 bar. This same standard state is also used for liquid mixtures of those components that exist as a liquid at the conditions of the mixture. Such substances are sometimes referred to as liquids that may act as a solvent. For substances that exist only as a solid or a gas in the pure component state at the temperature of the mixture, sometimes referred to as substances that can act only as a solute, the situation is more complicated, and standard states based on Henry s law may be used. In this case the pressure is again fixed at 1 bar, and thermal properties such as the standard-state enthalpy and heat capacity are based on the properties of the substance in the solvent at infinite dilution, but the standard-state Gibbs energy and entropy are based on a hypothetical state.of unit concentration (either unit molality or unit mole fraction, depending on the form of Henry s law used), with the standard-state fugacity at these conditions extrapolated from infinite-dilution behavior in the solvent, as shown in Fig. 9.1-3a and b. Therefore just as for a gas where the ideal gas state at 1 bar is a hypothetical state, the standard state of a substance that can only behave as a solute is a hypothetical state. However, one important characteristic of the solute standard state is that the properties depend strongly upon the solvent. used. Therefore, the standard-state properties are a function of the temperature, the solute, and the solvent. This can lead to difficulties when a mixed solvent is used. 

Thermal Properties of Nitration Acids. Heals of Solution. To determine the heat evolved during the actual process of nitration of a hydrocarbon by mixed acids, it is necessary to consider not only the heat of nitration but also various heats of solution. These may be obtained from the enthalpy chart developed by McKinley and Brown (Fig. 4-5). For each of the three components, the enthalpy is taken as zero at the standard state, consisting of the pure liquid component at a temperature of 32 F and a pressure of 1 atm. Plotted against the same abscissa but against different ordinates are the specific heat data for the system. From this figure, containing both 32 F relative enthalpies and specific heats, the enthalpy of any liquid mixtures of these components at ordinary temperatures can be readily calculated by reading the desired relative enthalpy at 32 F and the specific heat from the chart. 

Thermodynamic and transport properties of pure substances includes the various thermodynamic functions (//, S, G, Cp, etc.), density, vapor pressure, viscosity, thermal conductivity, and many others. These properties are functions of temperature and pressure, but an important subset consists of values defined under standard conditions, such as Af//°, the standard state enthalpy of formation of a compound from its elements. 

These tables summarize the thermophysical properties of air in the liquid and gaseous states as calculated from the pseudo-pure fluid equation of state of Lemmon et al. (2000). The first table refers to liquid and gaseous air at equilibrium as a function of temperature. The tabulated properties are the bubble-point pressure (i.e., pressure at which boiling begins as the pressure of the liquid is lowered) the dew-point pressure (i.e., pressure at which condensation begins as the pressure of the gas is raised) density (/ ) enthalpy (H) entropy (S) isochoric heat capacity (CJ isobaric heat capacity (C ) speed of sound (u) viscosity (rj) and thermal conductivity (A). The first line of identical temperatures is the bubble-point (liquid) and the second line is the dewpoint (vapor). The normal boiling point of air, i.e., the temperature at which the bubble-point pressure reaches 1 standard atmosphere (1.01325 bar), is 78.90 K (-194.25 °C). 

ELDAR contains data for more than 2000 electrolytes in more than 750 different solvents with a total of 56,000 chemical systems, 15,000 hterature references, 45,730 data tables, and 595,000 data points. ELDAR contains data on physical properties such as densities, dielectric coefficients, thermal expansion, compressibihty, p-V-T data, state diagrams and critical data. The thermodynamic properties include solvation and dilution heats, phase transition values (enthalpies, entropies and Gibbs free energies), phase equilibrium data, solubilities, vapor pressures, solvation data, standard and reference values, activities and activity coefficients, excess values, osmotic coefficients, specific heats, partial molar values and apparent partial molar values. Transport properties such as electrical conductivities, transference numbers, single ion conductivities, viscosities, thermal conductivities, and diffusion coefficients are also included. 

---