Endothermic

Temperature control. Let us now consider temperature control of the reactor. In the first instance, adiabatic operation of the reactor should be considered, since this leads to the simplest and cheapest reactor design. If adiabatic operation produces an unacceptable rise in temperature for exothermic reactions or an unacceptable fall in temperature for endothermic reactions, this can be dealt with in a number of ways ... 

This is an endothermic reaction accompanied by an increase in the number of moles. High conversion is favored by high temperature and low pressure. The reduction in pressure is achieved in practice by the use of superheated steam as a diluent and by operating the reactor below atmospheric pressure. The steam in this case fulfills a dual purpose by also providing heat for the reaction. 

Reaction temperature. For endothermic reactions. Fig. 2.9c shows that the temperature should be set as high as possible consistent with materials-of-construction limitations, catalyst life, and safety. For exothermic reactions, the ideal temperature is continuously decreasing as conversion increases (see Fig. 2.9c). 

Adiabatic operation. If adiabatic operation leads to an acceptable temperature rise for exothermic reactors or an acceptable fall for endothermic reactors, then this is the option normally chosen. If this is the case, then the feed stream to the reactor requires heating and the efiluent stream requires cooling. The heat integration characteristics are thus a cold stream (the reactor feed) and a hot stream (the reactor efiluent). The heat of reaction appears as elevated temperature of the efiluent stream in the case of exothermic reaction or reduced temperature in the case of endothermic reaction. 

Cold shot or hot shot. Injection of cold fresh feed for exothermic reactions or preheated feed for endothermic reactions to inter-... 

Figure 13.16 shows two possible thermal profiles for endothermic plug-fiow reactors. This time the temperature falls for low rates of heat addition and/or high heat of reaction. The temperature rises for the reverse conditions. Under conditions between the profiles shown in Fig. 13.16, a minimum can occur in the temperature profile at an intermediate point between the inlet and exit. 

If the reactor can be matched with other process streams (which is unlikely), then the reactor profile should be included in the heat integration problem. This would be a hot stream in the case of an exothermic reaction or a cold stream in the case of an endothermic reaction. 

Figure 13.4a shows an endothermic reactor integrated above the pinch. The endothermic reactor removes Qreact from the process above the pinch. The process above the pinch needs at least Qn in to... 

By contrast. Fig. 13.46 shows an endothermic reactor integrated below the pinch. The reactor imports Qreact from part of the process that needs to reject heat. Thus integration of the reactor serves to reduce the cold utility consumption by Qreact- There is an overall reduction in hot utility because, without integration, the process and reactor would require (Qumin + Qreact) from the utility. 

There is no obvious benefit from integrating an endothermic reactor above the pinch. The appropriate placement for endothermic reactors is below the pinch. ... 

The appropriate placement of reactors, as far as heat integration is concerned, is that exothermic reactors should be integrated above the pinch and endothermic reactors below the pinch. Care should be taken when reactor feeds are preheated by heat of reaction within the reactor for exothermic reactions. This can constitute cross-pinch heat transfer. The feeds should be preheated to pinch temperature by heat recovery before being fed to the reactor. 

Cracking reactions are endothermic the energy balance is obtained by the production of coke that deposits on the catalyst and that is burned in the regenerator. 

Reactive scattering or a chemical reaction is characterized by a rearrangement of the component particles within the collision system, thereby resulting in a change of the physical and chemical identity of the original collision reactants A + B into different collision products C + D. Total mass is conserved. The reaction is exothemiic when rel(CD) > (AB) and is endothermic when rel(CD) < (AB). A threshold energy is required for the endothemiic reaction. 

From the above discussion, we might expect that endothermic reactions for which the enthalpy change is large cannot take place. However, a further consideration of the equation... 

Most metals react exothermically with oxygen to form an oxide. Figure 3.4 shows how the value of AG for this process varies with temperature for a number of metals (and for carbon), and it can be seen that in all cases AG becomes less negative as the temperature is increased. However, the decomposition of these metal oxides into the metal and oxygen is an endothermic process, and Figure 3.4 shows that this process does not become even energetically feasible for the majority of metals until very high temperatures are reached. 

These values indicate a rapid fall in thermal stability of the halide from fluorine to iodine, and hydrogen iodide is an endothermic compound. If we now examine the various enthalpy changes involved. we find the following values (in kJ) ... 

Let us consider the formation of sodium chloride from its elements. An energy (enthalpy) diagram (called a Born-Haber cycle) for the reaction of sodium and chlorine is given in Figure 3.7. (As in the energy diagram for the formation of hydrogen chloride, an upward arrow represents an endothermic process and a downward arrow an exothermic process.)... 

To date there is no evidence that sodium forms any chloride other than NaCl indeed the electronic theory of valency predicts that Na" and CU, with their noble gas configurations, are likely to be the most stable ionic species. However, since some noble gas atoms can lose electrons to form cations (p. 354) we cannot rely fully on this theory. We therefore need to examine the evidence provided by energetic data. Let us consider the formation of a number of possible ionic compounds and first, the formation of sodium dichloride , NaCl2. The energy diagram for the formation of this hypothetical compound follows the pattern of that for NaCl but an additional endothermic step is added for the second ionisation energy of sodium. The lattice energy is calculated on the assumption that the compound is ionic and that Na is comparable in size with Mg ". The data are summarised below (standard enthalpies in kJ) ... 

There are many compounds in existence which have a considerable positive enthalpy of formation. They are not made by direct union of the constituent elements in their standard states, but by some process in which the necessary energy is provided indirectly. Many known covalent hydrides (Chapter 5) are made by indirect methods (for example from other hydrides) or by supplying energy (in the form of heat or an electric discharge) to the direct reaction to dissociate the hydrogen molecules and also possibly vaporise the other element. Other known endothermic compounds include nitrogen oxide and ethyne (acetylene) all these compounds have considerable kinetic stability. 

Although the data for the silver halides suggest that silver(I) fluoride is likely to be more soluble than the other silver halides (which is in fact the case), the hydration enthalpies for the sodium halides almost exactly balance the lattice energies. What then is the driving force which makes these salts soluble, and which indeed must be responsible for the solution process where this is endothermic We have seen on p. 66 the relationship AG = — TAS and... 

This melhod produces an endothermic hydride by indirect means. 

---