Electrodes standard hydrogen electrodes

Normal hydrogen electrode - standard hydrogen electrode... 

The physical setup that defines E° for a half-reaction is a hydrogen gas electrode (Standard Hydrogen Electrode) connected to an electrode where the half-reaction of interest takes place (let us say the l2 aq) + 2e 21" half-reaction see Fig. 7-2). The cell reaction for standard conditions, 25 , unit activities, and 1 atm Haoi pressure, is... 

Pavlishchuk and Addison [207] smdied the mutual potentials between various Ag /Ag electrodes in AN and the Fc /Fc couple in AN and also between these electrodes and various types of aqueous reference electrodes (standard hydrogen electrode, SCE, etc.). In the report, they showed that the literamre data on the half-wave potential of Fc /Fc couple in AN versus aqueous reference electrodes were scattered from one report to another. For example, the data versus aqueous SCE were scattered between 315 and 480 mV. Because most of the literature did not give detailed compositions of the junction, the reasmis for the scattering are not known. But the variation in the compositimi of the liquid junction between H2O and AN solutions and thus the variation in the LJP there seem to be one reason for that. 

The last example presented in this section deals with the pitting corrosion of Fe in CIO solutions. Perchlorate is less known as an aggressive ion but reveals some unique and remarkable characteristics with regard to pitting corrosion. For example, the critical pitting potential (1.46 V against a standard hydrogen electrode (SHE) for Fe/1 M NaClO ) can be measured with an accuracy of less than 4 mV [61] which is very unexpected if compared to... 

Figure 3-1 Voltage Measurements on a Silver-Silver Chloride, Hydrogen Cell at 298.15 K. The contribution of the Standard Hydrogen Electrode is taken as zero by convention.

Solid angle over which radi- Standard hydrogen electrode SHE... 

Standard Hydrogen Electrode The standard hydrogen electrode (SHE) is rarely used for routine analytical work, but is important because it is the reference electrode used to establish standard-state potentials for other half-reactions. The SHE consists of a Pt electrode immersed in a solution in which the hydrogen ion activity is 1.00 and in which H2 gas is bubbled at a pressure of 1 atm (Figure 11.7). A conventional salt bridge connects the SHE to the indicator half-cell. The shorthand notation for the standard hydrogen electrode is... 

Corrective action should be initiated when value is > — 0.23 V against the standard hydrogen electrode (SHE). Plant-specific values should be estabUshed for protection of stainless steels and nickel-based critical components. 

Laboratory experiments have shown that IGSCC can be mitigated if the electrochemical potential (ECP) could be decreased to —0.230 V on the standard hydrogen electrode (SHE) scale in water with a conductivity of 0.3 ]lS/cm (22). This has also been demonstrated in operating plants. Equipment has been developed to monitor ECP in the recirculation line and in strategic places such as the core top and core bottom, in the reactor vessel during power operation. 

Fig. 6. Band edge positions of several semiconductors ia contact with an aqueous electrolyte at pH 1 ia relation to the redox (electrode) potential regions (vs the standard hydrogen electrode) for the oxidation of organic functional groups (26,27).

Other Coordination Complexes. Because carbonate and bicarbonate are commonly found under environmental conditions in water, and because carbonate complexes Pu readily in most oxidation states, Pu carbonato complexes have been studied extensively. The reduction potentials vs the standard hydrogen electrode of Pu(VI)/(V) shifts from 0.916 to 0.33 V and the Pu(IV)/(III) potential shifts from 1.48 to -0.50 V in 1 Tf carbonate. These shifts indicate strong carbonate complexation. Electrochemistry, reaction kinetics, and spectroscopy of plutonium carbonates in solution have been reviewed (113). The solubiUty of Pu(IV) in aqueous carbonate solutions has been measured, and the stabiUty constants of hydroxycarbonato complexes have been calculated (Fig. 6b) (90). 

It must not be assumed that the protection potential is numerically equal to the equilibrium potential for the iron/ferrous-ion electrode (E ). The standard equilibrium potential (E ) for iron/ferrous-ion is -0-440V (vs. the standard hydrogen electrode). If the interfacial ferrous ion concentration when corrosion ceases is approximately 10 g ions/1 then, according to the Nernst equation, the equilibrium potential (E ) is given by ... 

Since the single potential of a metal cannot be measured it is necessary to use a suitable reference elecrode such as the Hg/Hg2Cl2/KCl electrode or the Ag/AgCl/KCl electrode, and although potentials are frequently expressed with reference to the standard hydrogen electrode (S.H.E.) the use of this electrode in practice is confined to fundamental studies rather than testing. 

It is apparent that since the electrode potential of a metal/solution interface can only be evaluated from the e.m.f. of a cell, the reference electrode used for that purpose must be specified precisely, e.g. the criterion for the cathodic protection of steel is —0-85 V (vs. Cu/CuSOg, sat.), but this can be expressed as a potential with respect to the standard hydrogen electrode (S.H.E.), i.e. -0-55 V (vs. S.H.E.) or with respect to any other reference electrode. Potentials of reference electrodes are given in Table 21.7. 

Table 21.6 Standard elearode potentials against the standard hydrogen electrode for inorganic systems at 25°Ct...

Electrode Potential (E) the difference in electrical potential between an electrode and the electrolyte with which it is in contact. It is best given with reference to the standard hydrogen electrode (S.H.E.), when it is equal in magnitude to the e.m.f. of a cell consisting of the electrode and the S.H.E. (with any liquid-junction potential eliminated). When in such a cell the electrode is the cathode, its electrode potential is positive when the electrode is the anode, its electrode potential is negative. When the species undergoing the reaction are in their standard states, E =, the stan-... 

When the activity of the ion M"+ is equal to unity (approximately true for a 1M solution), the electrode potential E is equal to the standard potential Ee. Some important standard electrode potentials referred to the standard hydrogen electrode at 25 °C (in aqueous solution) are collected in Table 2.5.5... 

It may be noted that the standard hydrogen electrode is rather difficult to manipulate. In practice, electrode potentials on the hydrogen scale are usually... 

When used as a standard electrode, the hydrogen electrode operates in a solution containing hydrogen ions at constant (unit) activity based usually on hydrochloric acid, and the hydrogen gas must be at 1 atmosphere pressure the effect of change in gas pressure is discussed in Ref. 28. 

The most widely used reference electrode, due to its ease of preparation and constancy of potential, is the calomel electrode. A calomel half-cell is one in which mercury and calomel [mercury(I) chloride] are covered with potassium chloride solution of definite concentration this may be 0.1 M, 1M, or saturated. These electrodes are referred to as the decimolar, the molar and the saturated calomel electrode (S.C.E.) and have the potentials, relative to the standard hydrogen electrode at 25 °C, of 0.3358,0.2824 and 0.2444 volt. Of these electrodes the S.C.E. is most commonly used, largely because of the suppressive effect of saturated potassium chloride solution on liquid junction potentials. However, this electrode suffers from the drawback that its potential varies rapidly with alteration in temperature owing to changes in the solubility of potassium chloride, and restoration of a stable potential may be slow owing to the disturbance of the calomel-potassium chloride equilibrium. The potentials of the decimolar and molar electrodes are less affected by change in temperature and are to be preferred in cases where accurate values of electrode potentials are required. The electrode reaction is... 

Electrode Potential vs standard hydrogen electrode (volts) ... 

Eq. (8)] represents by definition the zero point of the electrochemical potential scale (standard hydrogen electrode, often denoted SHE). 

Figure 2 illustrates the resulting situation. Due to the strong acidic solution in the battery, it corresponds lo Fig. 1 for small pH values, but here the electrode potential is drawn on the vertical axis. The values are referred to the above-mentioned standard hydrogen electrode. To enlarge the scale, the range between 0 and 1.2 V is omitted. 

---