Electrode potential electrochemical oxidation

Rh(QI) and Ir(III) Complexes. A number of Rh(III) and some Ir(III) complexes have been investigated thoroughly by CV [78-81]. The values for the electrode potentials for oxidation and for reduction are given in Table 1. The electrochemical behavior of the cyclometallated complexes differs strongly from that of their diimin analogs, but it is completely in line with the spectral and reactivity characteristics. 

FIGURE7.1. Time series of the potential ofaPt electrode during electrochemical oxidation of H2 in the presence of copper ions at different current densities [5]. 

Electrochemical methods are preferred in analysis of phenols and halogenated organics since often there is no need for extensive separation. However direct determination on noble metal electrodes is not favored due to high over-potentials. Electrochemical oxidation of phenols readily occurs on unmodified electrodes, but oxidation results in the formation of dimers which poison the electrodes, decreasing the oxidation currents. In order to improve sensitivity and selectivity, chemically modified electrodes are employed. In this regard M-N4 complexes have shown remarkable catalytic activity towards the detection of phenols and other species when either employed as homogeneous catalysts or when adsorbed to electrodes. 

At the sensing electrode, the electrochemical oxidation (Eq. 17.13) and reduction (Eq. 17.12) occur simultaneously and establish a local cell. When the rates of these reactions are equal to one another, the potential of the sensing electrode is a mixed potential. 

Atmospheric corrosion is electrochemical ia nature and depends on the flow of current between anodic and cathodic areas. The resulting attack is generally localized to particular features of the metallurgical stmcture. Features that contribute to differences ia potential iaclude the iatermetaUic particles and the electrode potentials of the matrix. The electrode potentials of some soHd solutions and iatermetaUic particles are shown ia Table 26. Iron and sUicon impurities ia commercially pure aluminum form iatermetaUic coastitueat particles that are cathodic to alumiaum. Because the oxide film over these coastitueats may be weak, they can promote electrochemical attack of the surrounding aluminum matrix. The superior resistance to corrosion of high purity aluminum is attributed to the small number of these constituents. 

The thermodynamics of electrochemical reactions can be understood by considering the standard electrode potential, the potential of a reaction under standard conditions of temperature and pressure where all reactants and products are at unit activity. Table 1 Hsts a variety of standard electrode potentials. The standard potential is expressed relative to the standard hydrogen reference electrode potential in units of volts. A given reaction tends to proceed in the anodic direction, ie, toward the oxidation reaction, if the potential of the reaction is positive with respect to the standard potential. Conversely, a movement of the potential in the negative direction away from the standard potential encourages a cathodic or reduction reaction. 

The changes in the optical absorption spectra of conducting polymers can be monitored using optoelectrochemical techniques. The optical spectmm of a thin polymer film, mounted on a transparent electrode, such as indium tin oxide (ITO) coated glass, is recorded. The cell is fitted with a counter and reference electrode so that the potential at the polymer-coated electrode can be controlled electrochemically. The absorption spectmm is recorded as a function of electrode potential, and the evolution of the polymer s band stmcture can be observed as it changes from insulating to conducting (11). 

Pourbaix, M., Recent Applications of Electrode Potential Measurements in the Thermodynamics and Kinetics of Corrosion of Metals , Corros., 25, 267 (1969) de Nora, O., Gallone, P., Traini, C. and Meneghini, G., On the Mechanism of Anodic Chlorate Oxidation , J. Electrochem. Soc., 116, 147 (1969)... 

Turning now to the acidic situation, a report on the electrochemical behaviour of platinum exposed to 0-1m sodium bicarbonate containing oxygen up to 3970 kPa and at temperatures of 162 and 238°C is available. Anodic and cathodic polarisation curves and Tafel slopes are presented whilst limiting current densities, exchange current densities and reversible electrode potentials are tabulated. In weak acid and neutral solutions containing chloride ions, the passivity of platinum is always associated with the presence of adsorbed oxygen or oxide layer on the surface In concentrated hydrochloric acid solutions, the possible retardation of dissolution is more likely because of an adsorbed layer of atomic chlorine ... 

Figure 16. Activation barrier A for the formation of a breakthrough pore in a thin surface oxide film on metal as a function of electrode potential at two different surface tensions, om, of the metal/electrolyte interface.7The solid lines indicate the values of A b against Aand the dotted lines correspond to die critical potentials for the pore formation. ACd= 1 F m-2, a = 0.01 J m-2, h = 2 x 10-9 m, a, am = 0.41 J m 2 b, am 0.21 J m 2 (From N. Sato, J. Electmchem. Soc. 129, 255, 1982, Fig. 3. Reproduced by permission of The Electrochemical Society, Inc.)...

The equilibrium (1) at the electrode surface will lie to the right, i.e. the reduction of O will occur if the electrode potential is set at a value more cathodic than E. Conversely, the oxidation of R would require the potential to be more anodic than F/ . Since the potential range in certain solvents can extend from — 3-0 V to + 3-5 V, the driving force for an oxidation or a reduction is of the order of 3 eV or 260 kJ moR and experience shows that this is sufficient for the oxidation and reduction of most organic compounds, including many which are resistant to chemical redox reagents. For example, the electrochemical oxidation of alkanes and alkenes to carbonium ions is possible in several systems... 

Certain three-dimensional electrodes, also known as slurry or fluidized-bed electrodes, are sometimes used as well in order to have a strongly enhanced working surface area. Electrodes of this type consist of fine particles of the electrode material (metal, oxide, carbon, or other) kept in suspension in the electrolyte solution by intense mixing or gas bubbling. A certain potential difference is applied to the system between an inert feeder elecnode and an auxiliary electrode that are immersed into the suspension. By charge transfer, the particles of electrode material constantly hitting the feeder electrode acquire its potential (fully or at least in part), so that a desired electrochemical reaction may occur at their surface. In this reaction, the particles lose their charge but reacquire it in subsequent encounters with the feeder electrode. 

Oxides of various metals are a broad class of electrode materials useful in many electrochemical processes (Trasatti, 1980-1981). The surfaces of practically all metals (both base and noble) become covered by layers of chemisorbed oxygen upon anodic polarization. The composition and properties of these layers depend on potential, on the electrolyte, and on the electrolysis conditions. They are often rather thick and have a distinct phase character, so that the metal electrode is converted to a typical oxide electrode. One can also make electrodes directly from oxides deposited in some way or other on various conducting substrates. 

Many dehydrogenase enzymes catalyze oxidation/reduction reactions with the aid of nicotinamide cofactors. The electrochemical oxidation of nicotinamide adeniiw dinucleotide, NADH, has been studied in depthThe direct oxidation of NADH has been used to determine concentration of ethanol i s-isv, i62) lactate 157,160,162,163) pyTuvate 1 ), glucose-6-phosphate lactate dehydrogenase 159,161) alanine The direct oxidation often entails such complications as electrode surface pretreatment, interferences due to electrode operation at very positive potentials, and electrode fouling due to adsorption. Subsequent reaction of the NADH with peroxidase allows quantitation via the well established Clark electrode. 

---