E-test

CEN TC 54 (Unfired pressure vessels) WG E (Testing and inspection) Draft for the EN Standard"... 

A two-tailed E-test of the following null and alternative hypotheses... 

For a power frequency voltage withstand test a d.c. test is generally not recommended on a.e. equipment, unless only d.c., test voltage is available at the plaee of testing. The d.e. test values, as above, are therefore for such eventualities only and are equivalent to power frequency a.c. voltage withstand test values. 

Maimenance records such as critical instruiueni checks, pressure relief vah e tests, pressure vessel inspections... 

In analysis of variance, the variance due to each source of variation is systematically isolated. A test of significance, the E-test, is then applied to establish roughly how seriously one must regard each source of variation. The interested reader is urged to consult books on statistics14 for discussions of this valuable statistical method. 

Fig. 6.1. Yield strengths of the five polymers are plotted against 1/MC that is the inverse molecular mass between crosslinks. The diamond represents polymer E. Test temperature 23 °C. a and b represent results of flexural tests on small samples (thickness 1.3 mm) a annealed, b quenched,...

Fig. 6.5. Yield strengths from flexural tests are plotted against strain rates at the surface of the samples. Tests were performed on polymers A, B, and E test temperature 23 °C. The slope of the three lines correspond to similar activation volumes v = 2 0.1 nm3...

Sh E-Test 4.4A A sample of neon of volume 10.0 L at 300. Torr is allowed to expand isothermally into an evacuated tube with a volume of 20.0 L. What is the final pressure of the neon in the tube ... 

Sei e-Test 12.13A Predict the products resulting from the electrolysis of l M AgNOj(aq). 

Subpart E - Testing Facilities Operation Sec. 58.81 Standard operating procedures. Sec. 58.83 Reagents and solutions. 

This homogeneity value will become positive when the null hypothesis is not rejected by Fisher s E-test (F < Ei a)Vl)V2) and will be closer to 1 the more homogeneous the material is. If inhomogeneity is statistically proved by the test statistic F > Fi a>VuV2, the homogeneity value becomes negative. In the limiting case F = hom(A) becomes zero. 

The transformation is global. The schemes P and P are strongly computationally equivalent in the restricted sense - if we omit from the test added computational histories of (P,I, a) and (P, I, a) all values of the new variables and all tests involving these variables (i.e. test Z ) for an interpretation I extending I to all of P and P, then the resulting lists are equal. However the loop structure of P has been drastically changed and there is no simple relationship between the graphs of P and P. ... 

As presented in Figure 15.10, after 100 h TOS the permeate valve was closed, and thus the transmembrane pressure fell to zero. The pilot plant remained in a standby mode and unmanned for approximately 75 h. During this period, the catalyst slurry was circulated through the cross-flow filter, without permeate flow radially through the filter membrane (i.e., test conditions were constant with the... 

Examine data for unreliable results. Establish that both sets have similar precisions by / -test. Apply E-test (equation (2.10))... 

Batch tests (i. e., tests on individual waste materials) are conducted with the provided solid suspensions (e.g., soils such as Woodburn, Sagehill, and Olyic, as well as two bottom sediment samples) prepared with previously air-dried solids (i. e., soils and bottom sediments), ground to a uniform powdery texture for mixing with the eluates from the 24-h batch leaching test of the different SWMs/COMs. The concentrations of eluates in solution were designed to evaluate the capability of different environmental solids to adsorb available contaminants. The solid particles were fully dispersed with the aqueous phase to achieve complete adsorption. Common practice is to use a solid solution ratio of 1 g 4 ml [ 1 ], together with proper tumbling of the samples at a constant temperature (e.g., at least 24 h in a constant temperature environment of 20°C). 

The accuracy of a method is defined as the closeness of the value obtained to known or accepted values. Accuracy can be determined in a number of ways, depending on the nature of the CZE method and availability of orthogonal techniques to compare results. If practical, spike recovery studies (i.e., testing to determine whether recovery matches the amount of a known analyte or impurity spiked) are good alternatives to orthogonal assay comparisons. ICH guidelines also allow method accuracy to be inferred, once specificity, linearity, and precision are established. 

Figure 6.17. Schematic diagram of apparatus for galvanostatic measurements P, constant current power supply e, test electrode e2, reference electrode counter (auxiliary)-electrode V, potential-time recording instrument.

A.2. Quick-E-Test in the Lipase- or Esterase-Catalyzed Kinetic Resolution of Chiral p-Nitrophenyl Esters... 

American College of Medical Genetics/American Society of Human Genetics Working Group on ApoE and Alzheimer Disease, Statement on use of apolipoprotein E testing for Alzheimer disease. JAMA 274(20), 1627-1629 (1995). 

SUBPART E TESTING FACILITIES OPERATION 58.81 Standard Operating Procedures... 

All changes in specifications from those in the approved application must be submitted in a prior approval supplement unless otherwise exempted by regulation or guidance (506A(c)(2)(A)). Specifications (i.e., tests, analytical procedures, and acceptance criteria) are the quality standards provided in an approved application to confiim the quality of drug substances, drug products, intermediates, raw ma-... 

---