Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Dynamics of a shell-and-tube heat exchanger

HEATEX - Dynamics of a Shell-and-Tube Heat Exchanger... [Pg.622]

Gas-Liquid Mixing and Mass Transfer 385 Dynamics of a Shell-and-Tube Heat Exchanger 511 Semi-Batch Manufacture of Hexamethylene-triamine 353... [Pg.607]

Guideline 8 The manipulated variables should affect the controlled variables directly, rather than indirectly. Compliance with this guideline usually results in a control loop with favorable static and dynamic characteristics. For example, consider the problem of controlling the exit temperature of a process stream that is heated by steam in a shell and tube heat exchanger. It is preferable to throttle the steam flow to the heat exchanger rather than the condensate flow from the shell, because the steam flow rate has a more direct effect on the steam pressure and on the rate of heat transfer. [Pg.240]

The determination of the process mathematical model is often the most difficult and time-consuming step in control system analysis. This is a result of the dynamic nature of the process in other words, how the system reacts during upsets or disturbances. The problem is further complicated by process nonlinearities and time-varying parameters. To illustrate the modelling procedure we will look at developing a model for a shell and tube heat exchanger with temperature control [7], shown in Figure 3.29. [Pg.81]

In this chapter different types of heat exchanger will be analyzed for their dynamic behavior. The first type is the shell and tube type, where steam condenses inside the tubes and the contents of a well-mixed tank or reactor have to be heated. The second type is also a shell and tube type heat exchanger, where the steam condenses outside the tubes (shell-side) and the liquid to be heated flows through the tubes. The last type is the countercurrent heat exchanger, in which the liquid to be heated flows countercurrent to the heating medium. [Pg.195]

Eluor Daniel has the ability to perform a heat exchanger tube rupture transient analysis consistent with the method referred to in RP-521 ("Model to Predict Transient Consequences of a Heat Exchanger Tube Rupture," by Sumaria et ah). This methodology accounts for effects such as the inertia of the low-pressure liquid, the compressibility of the liquid, the expansion of the exchanger shell or tube chaimels, and the relief valve dynamics. Dynamic simulation can be used to meet the following objectives ... [Pg.51]

At each point in the heat exchanger, heat passes from the hotter fluid to the tube wall, and then from the tube wall to the cooler fluid. The tube wall will have its own dynamic response, and, just as it separates physically the two fluids, so it separates mathematically the calculations of the two fluid temperatures. Heat will also flow between the shell fluid and the shell wall, which will normally be heavily insulated to prevent heat flow to the environment. The shell wall will be relatively massive and cause a signiflcant slowing of the response of the shell-side fluid outlet temperature. [Pg.257]


See other pages where Dynamics of a shell-and-tube heat exchanger is mentioned: [Pg.47]    [Pg.45]    [Pg.45]    [Pg.132]    [Pg.44]    [Pg.3]    [Pg.1350]    [Pg.205]    [Pg.1049]    [Pg.256]    [Pg.393]    [Pg.1236]    [Pg.724]    [Pg.14]    [Pg.696]   
See also in sourсe #XX -- [ Pg.511 ]




SEARCH



A. Dynamics

Dynamic exchange

Dynamics of a shell-and-tube heat

Dynamics of exchange

HEATEX - Dynamics of a Shell-and-Tube Heat Exchanger

Heat dynamics

Heat exchanger dynamics

Heat exchanger tube

Heat exchanger tubing

Heat exchangers shells

Heating, dynamics

Shell and tube heat exchanger

Shell exchange

Shell-and-tube exchangers

Shell-and-tube exchangers shells

Shell-and-tube heat

Shell-and-tube heat exchangers tubes

Tube exchangers

© 2024 chempedia.info