Dry gels

Sephadex G-X Specific volume water mL/g dry gel Permeabihty, iC Operating pressure, kPa Flowrate water, mL/(cm h)... 

The dried polyoxazoline-modified silica gel was immersed into distilled water. The adsorption property of the resulting gel was estimated by the water content. The water uptake was calculated from an expression of (W -W)jW, where Wis the weight of dried gel and W is the weight of water-absorbed gel. The modified gel showed a higher water-adsorption property than that of untreated silica gel, which absorbed 10.8 multiples of water. The water uptake of modified gel was up to 13.7 multiples of the weight of dried gel. Thus, silica gel has been made more hydrophilic by a polyoxazoline segment. 

Calculated from feed ratio. b Calculated from elemental analysis. c g wet gel/g dried gel. d o = Si(OEt),... 

TS-l/MCM-41 catalysts synttiesized by the dry gel conversion method are shown to have hexagonal mesopores. The catalytic activity of synthesized TS-l/MCM-41 catalysts was tested with qroxidation reaction of olefins to reved that both the conversion of olefins and selectivity to epoxide are higher than those of H-MCM-41,... 

In this work, highly active epoxidation catalysts, which have hydrophobic surface of TS-1, were synthesized by the dry gel conversion (DGC) method. Ti-MCM-41 was synthesized first by a modifed method and the TS-l/MCM-41 catalysts were subsequently synthesized by the DGC method. The catalysts were characterized by the XRD, BET, FT-IR, and UV-VIS spectroscopy. TS-l/MCM-41 catalysts were applied to the epoxidation of 1-hexene and cyclohexene with aqueous H202to evaluate their activities for the epoxidation reaction. ... 

Titanium containing hexagonal mesoporous materials were synthesized by the modified hydrothermal synthesis method. The synthesized Ti-MCM-41 has hi y ordered hexa rud structure. Ti-MCM-41 was transformed into TS-l/MCM-41 by using the dry gel conversion process. For the synthesis of Ti-MCM-41 with TS-1(TS-1/MCM-41) structure TPAOH was used as the template. The synthesized TS-l/MCM-41 has hexagonal mesopores when the DGC process was carried out for less than 3 6 h. The catalytic activity of synthesized TS-l/MCM-41 catalysts was measured by the epoxidation of 1-hexene and cyclohexene. For the comparison of the catalytic activity, TS-1 and Ti-MCM-41 samples were also applied to the epoxidation reaction under the same reaction conditions. Both the conversion of olefins and selectivity to epoxide over TS-l/MCM-41 are found hi er flian those of other catalysts. 

Assays. Protein concentrations were measured by the method of Bradford (18) and the various contractile protein ATPase activities by tRe method of Martin and Doty (19). Gel electrophoresis was carried out by the method of Ames (20) on 1.5 ran polyacrylamide slabs using the discontinuous SDS buffer system of Laemnli (21). Dried gels were scanned at 550 nm for densiometry measurements. 

Both xerogels and aerogels are characteristically high surface area materials (surface areas normally exceed 500 m2/g). Unlike wet gels, many uses exist for dried gels due to their high surface areas and small pore sizes (typically, < 20 nm diameters). Examples include catalyst supports (12.). ultrafiltration media (18), antireflective coatings (19-20), and ultra-low dielectric constant films. (Lenahan, P. M. and Brinker, C. J., unpublished results.)... 

Solid state MASS 29Si NMR spectra of dried gels prepared with 4 equivalents of water show a similar trend. QJ-Q4 species are evident in gels prepared under neutral conditions (41), whereas under more basic conditions, Q1 species are absent and Q2 species are greatly reduced relative to Q4 (see NMR results presented below). Thus the effects of restructuring are preserved in the fully dried gel. 

The Raman spectra (0-1400 cm l) shown in Fig re 6 illustrate the structural changes which accompany the consolidation of silica gels. The 1100°C sample is fully dense, whereas the 50 and 600°C samples have high surface areas (1050 and 890 m2/g), respectively. The important features of the Raman spectra attributable to siloxane bond formation are the broad band at about 430 cm 1 and the sharp bands at 490 and 608 cm 1(which in the literature have been ascribed to defects denoted as D1 and D2, respectively). The D2 band is absent in the dried gel. It appears at about 200°C and becomes very intense at intermediate temperatures, 600-800°C. Its relative intensity in the fully consolidated gel is low and comparable to that in conventional vitreous silica. By comparison the intensities of the 430 and 490 cm 1 bands are much more constant. Both bands are present at each temperature, and the relative intensity of the 430 cm 1 band increases only slightly with respect to D1 as the temperature is increased. Figure 7 shows that in addition to elevated temperatures the relative intensity of D2 also decreases upon exposure to water vapor. 

All copolymers were prepared by solution polymerization, under adiabatic conditions, giving at least 99.9% conversions. The polymer gels were granulated and then dried at 90 °C to a residual water content of 10 to 12%. The active polymer content of each sample was calculated from the initial weight of the comonomers and the weight of the dried gel. Hydrolysis of the polymers was determined by conductometric titration to be less than 0.2% of the acrylamide charge. The molecular weight of the polymers was 8-10 million as determined by intrinsic viscosity measurements. 

According to the packing geometry, the systems present different porosity and specific surface. The final characteristics of the dried gel are determined by the physicochemical conditions at every step of the preparation the size of primary particles at the moment of aggregate, the concentration of particles in solution, the pH, salt concentration, temperature, and time of aging or other treatment in the wet state, mechanical forces present during drying, the temperature, pH, pressure, salt... 

Relative molecular mass distributions for components of biochemical and polymer systems can be determined with a 10% accuracy using standards. With biochemical materials, where both simple and macro-molecules may be present in an electrolyte solution, desalting is commonly employed to isolate the macromolecules. Inorganic salts and small molecules are eluted well after such materials as peptides, proteins, enzymes and viruses. Desalting is most efficient if gels with relatively small pores are used, the process being more rapid than dialysis. Dilute solutions of macro-molecules can be concentrated and isolated by adding dry gel beads to absorb the solvent and low RMM solutes. 

---