Diene elastomers polymerizations

A variation of the sequential monomer addition technique described in Section 9.2.6(i) is used to make styrene-diene-styrene iriblock thermoplastic rubbers. Styrene is polymerized first, using butyl lithium initiator in a nonpolar solvent. Then, a mixture of styrene and the diene is added to the living polystyryl macroanion. The diene will polymerize first, because styrene anions initiate diene polymerization much faster than the reverse process. After the diene monomer is consumed, polystyrene forms the third block. The combination of Li initiation and a nonpolar solvent produces a high cis-1,4 content in the central polydiene block, as required for thermoplastic elastomer behavior. 

Low-temperature solution processes are state-of-the-art for the production of ethylene/propylene or ethylene/propylene/diene elastomers (EPDR or EPDM). A continuous stirred-tank reactor (CSTR) or a series of two or even more such reactors is used [2]. n-Hexane, n-heptane, or Ce, C7 fractions are the solvents. Catalyst, co-catalyst and other compounds are introduced with the solvent into the reactor. The monomers (ethylene, propylene) are injected as gases other olefins are introduced in liquid form. The polymerization process runs around 50 °C and at pressures up to 2 MPa. Downstream the catalyst/co-catalyst system is deactivated and their residues are dissolved in dilute acid or aqueous NaOH. The copolymer is stabilized with an antioxidant. Steam treatment removes the rest of the solvent and monomers, and agglomerates the product to crumbs. These crumbs are then dried and finished to bales or pellets. 

Polymerization and Copolymerization of Dienes. Diene monomers can be polymerized to elastomers by bulk, solution, suspension, or emulsion processes. In commercial practice virtually all the diene elastomers are, however, prepared by the emulsion process. Some basic recipes used for preparing various types of synthetic rubber are shown in Table 15-17. 

Figure 35 4. Loss modulus, C, as a function of temperature for a poly(buta-diene) elastomer produced by emulsion polymerization, E>BR, an E>BR grafted with styrene E-Br-g-S, a poly(styrene), PS, and a high-impact poly(styrene) produced by in situ polymerization of styrene in a solution of E-BR in styrene, HIPS. The peaks give the dynamic glass transition temperatures. (After data by H. Willersinn.)...

A very useful source of information on polymerization chemistry of the diene elastomers.)... 

As mentioned in section 20.2.3, natural rubber (in common with other diene elastomers) is readily attacked by ozone. The mechanism of the reaction is probably the same as that established for simple olefins [10]. In this case, the initial product is a -complex which cleaves to form an aldehyde or ketone and a zwitterion. Several subsequent reactions may then occur, depending on the nature of the reactants and conditions. The zwitterion may dimerize or polymerize or react with the carbonyl compound to form an ozonide ... 

The elastomer produced in greatest amount is styrene-butadiene rubber (SBR) Annually just under 10 lb of SBR IS produced in the United States and al most all of it IS used in automobile tires As its name suggests SBR is prepared from styrene and 1 3 buta diene It is an example of a copolymer a polymer as sembled from two or more different monomers Free radical polymerization of a mixture of styrene and 1 3 butadiene gives SBR... 

Sodium is a catalyst for many polymerizations the two most familiar are the polymerization of 1,2-butadiene (the Buna process) and the copolymerization of styrene—butadiene mixtures (the modified GRS process). The alfin catalysts, made from sodium, give extremely rapid or unusual polymerizations of some dienes and of styrene (qv) (133—137) (see Butadiene Elastomers, synthetic Styrene plastics). 

Elastomers. Ethylene—propylene terpolymer (diene monomer) elastomers (EPDM) use a variety of third monomers during polymerization (see Elastomers, ethyiene-propylene-diene rubber). Ethyhdenenorbomene (ENB) is the most important of these monomers and requires dicyclopentadiene as a precursor. ENB is synthesized in a two step preparation, ie, a Diels-Alder reaction of CPD (via cracking of DCPD) with butadiene to yield 5-vinylbicyclo[2.2.1]-hept-2-ene [3048-64-4] (7) where the external double bond is then isomerized catalyticaHy toward the ring yielding 5-ethyhdenebicyclo[2.2.1]-hept-2-ene [16219-75-3] (ENB) (8) (60). 

The first sulfur curable copolymer was prepared ia ethyl chloride usiag AlCl coinitiator and 1,3-butadiene as comonomer however, it was soon found that isoprene was a better diene comonomer and methyl chloride was a better polymerization diluent. With the advent of World War II, there was a critical need to produce synthetic elastomers in North America because the supply of natural mbber was drastically curtailed. This resulted in an enormous scientific and engineering effort that resulted in commercial production of butyl mbber in 1943. 

ADMET is quite possibly the most flexible transition-metal-catalyzed polymerization route known to date. With the introduction of new, functionality-tolerant robust catalysts, the primary limitation of this chemistry involves the synthesis and cost of the diene monomer that is used. ADMET gives the chemist a powerful tool for the synthesis of polymers not easily accessible via other means, and in this chapter, we designate the key elements of ADMET. We detail the synthetic techniques required to perform this reaction and discuss the wide range of properties observed from the variety of polymers that can be synthesized. For example, branched and functionalized polymers produced by this route provide excellent models (after quantitative hydrogenation) for the study of many large-volume commercial copolymers, and the synthesis of reactive carbosilane polymers provides a flexible route to solvent-resistant elastomers with variable properties. Telechelic oligomers can also be made which offer an excellent means for polymer modification or incorporation into block copolymers. All of these examples illustrate the versatility of ADMET. 

As to the first route, we started in 1969 (1) in investigating unconventional transition metal complexes of the 5 and 4f block elements of periodic table, e.g., actinides and lanthanides as catalysts for the polymerization of dienes (butadiene and isoprene) with an extremely high cis content. Even a small increase of cistacticity in the vicinity of 100% has an important effect on crystallization and consequently on elastomer processability and properties (2). The f-block elements have unique electronic and stereochemical characteristics and give the possibility of a participation of the f-electrons in the metal ligand bond. 

Besides butadiene, another important monomer for the synthetic elastomer industry is chloroprene, which is polymerized to the chemically resistant polychloroprene. It is made by chlorination of butadiene follow by dehydrochlorination. As with most conjugated dienes, addition occurs either 1,2 or 1,4 because the intermediate allyl carbocation is delocalized. The 1,4-isomer can be isomerized to the 1,2-isomer by heating with cuprous chloride. 

Conjugated dienes such as 1,3-butadiene very readily polymerize free radically. The important thing to remember here is that there are double bonds still present in the polymer. This is especially important in the case of elastomers (synthetic rubbers) because some cross-linking with disulfide bridges (vulcanization) can occur in the finished polymer at the allylic sites still present to provide elastic properties to the overall polymers. Vulcanization will be discussed in detail in Chapter 18, Section 3. The mechanism shown in Fig. 14.3 demonstrates only the 1,4-addition of butadiene for simplicity. 1,2-Addition also occurs, and the double bonds may be cis or trans in their stereochemistry. Only with the metal complex... 

Many of the synthetic elastomers now made are still polymerized by a free radical mechanism. Polychloroprene, polybutadiene, polyisoprene, and styrene-butadiene copolymer are made this way. Initiation by peroxides is common. Many propagation steps create high molecular weight products. Review the mechanism of free radical polymerization of dienes given in Chapter 14, Section 2.2. 

The polymerization and copolymerization of 1,3-dienes is of commercial importance in the annual production of over 4 billion pounds of elastomers and about 2 billion pounds of plastics in the United States (Secs. 6-8 and 8-10). 

In addition to the triblock thermoplastic elastomers, other useful copolymers of styrene with a diene are produced commerically by living anionic polymerization. These include di-and multiblock copolymers, random copolymers, and tapered block copolymers. A tapered (gradient) copolymer has a variation in composition along the polymer chain. For example, S-S/D-D is a tapered block polymer that tapers from a polystyrene block to a styrene-diene random copolymer to polydiene block. (Tapered polymers need not have pure blocks at their ends. One can have a continuously tapered composition from styrene to diene by... 

The annual worlwide production of triblock thermoplastic elastomers, clear impact-resistant polystyrene, and other styrene-diene products produced by anionic polymerization exceeds a couple of billion pounds. (Commercial utilization of anionic polymerization also includes the polymerization of 1,3-butadiene alone.)... 

Terpolymerization, the simultaneous polymerization of three monomers, has become increasingly important from the commercial viewpoint. The improvements that are obtained by copolymerizing styrene with acrylonitrile or butadiene have been mentioned previously. The radical terpolymerization of styrene with acrylonitrile and butadiene increases even further the degree of variation in properties that can be built into the final product. Many other commercial uses of terpolymerization exist. In most of these the terpolymer has two of the monomers present in major amounts to obtain the gross properties desired, with the third monomer in a minor amount for modification of a special property. Thus the ethylene-propylene elastomers are terpolymerized with minor amounts of a diene in order to allow the product to be subsquently crosslinked. 

Gheneim R, Perez-Beramen C, Gandini A. Diels-Alder reactions with novel polymeric dienes and dienophiles synthesis of reversibly cross-linked elastomers. Macromolecules 2002 35 7246-7253. 

---