Diazoalkanes, reaction with rhodium catalyzed

Carbene itself ( CH2) is extremely reactive and gives many side reactions, especially insertion reactions (12-21), which greatly reduce yields. This competition is also true with rhodium-catalyzed diazoalkane cyclopropanations (see below). When it is desired to add CH2 for preparative purposes, free carbene is not used, but the Simmons-Smith procedure (p. 1241) or some other method that does not involve free carbenes is employed instead. Halocarbenes are less active than carbenes, and this reaction proceeds quite well, since insertion reactions do not interfereThe absolute rate constant for addition of selected alkoxychlorocar-bene to butenes has been measured to range from 330 to 1 x 10 A few of the many ways in which halocarbenes or carbenoids are generated for... 

Reaction of diazo compounds with a variety of transition metal compounds leads to evolution of nitrogen and formation of products of the same general type as those formed by thermal and photochemical decomposition of diazoalkanes. These transition metal-catalyzed reactions in general appear to involve carbenoid intermediates in which the carbene becomes bound to the metal.83 The metals which have been used most frequently in synthesis are copper and rhodium. 

Allyl sulfides and allyl amines. Rhodium-catalyzed decomposition of ethyl diazoacetate in the presence of these allyl compounds generates products 136 and 137, respectively, derived from [2,3] rearrangement of an S- or N-ylide intermediate, besides small amounts of carbene dimers No cyclopropane and no product resulting from the ylide by [1,2] rearrangement were detected. Besides RhjfOAc) and Rhg(CO)i6, the rhodium(I) catalysts [(cod)RhCl]2 and [(CO)2RhCl]2 were found to behave similarly, but yields with the only allyl amine tested, CH =CH—CH NMe, were distinctly lower with the latter two catalysts. Reaction temperatures are higher than usually needed in rhodium-promoted diazoalkane decomposition, which is certainly due to competition between the diazo compound and the allylic hetero-... 

The transition metal-catalyzed cyclopropanation of alkenes is one of the most efficient methods for the preparation of cyclopropanes. In 1959 Dull and Abend reported [617] their finding that treatment of ketene diethylacetal with diazomethane in the presence of catalytic amounts of copper(I) bromide leads to the formation of cyclopropanone diethylacetal. The same year Wittig described the cyclopropanation of cyclohexene with diazomethane and zinc(II) iodide [494]. Since then many variations and improvements of this reaction have been reported. Today a large number of transition metal complexes are known which react with diazoalkanes or other carbene precursors to yield intermediates capable of cyclopropanating olefins (Figure 3.32). However, from the commonly used catalysts of this type (rhodium(II) or palladium(II) carboxylates, copper salts) no carbene complexes have yet been identified spectroscopically. 

The reactions illustrated in equations (62-64) are each catalyzed by rhodium acetate. Diazo compounds, especially diazoalkanes, can also react by a simple ionic mechanism. The esterification of a carboxylic acid with diazomethane is a familiar example. The ionic pathway is especially likely when the intermediate carbocation would be stabilized. Thus, diazine (158) couples smoothly with phenols, presumably by thermal rearrangement to the corresponding diazo sugar, followed by acid-catalyzed N2 loss... 

In contrast to the wealth of chemistry reported for catalyzed reactions of diazocarbonyl compounds, there are fewer applications of diazomethane as a carbenoid precursor. Catalytic decomposition of diazomethane, CH2N2, has been reported as a general method for the methylenation of chemical compounds [12]. The efficacy of rhodium catalysts for mediating carbene transfer from diazoalkanes is poor. The preparative use of diazomethane in the synthesis of cyclopropane derivatives from olefins is mostly associated with the employment of palladium cat-... 

The reaction system (6-37) includes the thermal azo-extrusion of a cyclic azo compound to a cyclopropane derivative and the direct formation of cyclopropanes, catalyzed by metal complexes. Synthetic routes to cyclopropane derivatives became an important subject in the last two decades, and one frequently used method is the 1,3-dipolar cycloaddition of a diazoalkane to an alkene followed by thermal or photolytic azo-extrusion of the 4,5-dihydro-3//-pyrazole formed to the cyclopropane derivative (6-37 A). This route can be followed in many cases without isolation, or even without direct observation, of the 4,5-dihydro-3//-pyrazole. Therefore, it is formally very similar to cyclopropane formation from alkenes with diazoalkanes, in which a carbene is first formed by azo-extrusion of the diazoalkane (see Sect. 8.3). As shown in pathway (6-37 B), this step can be catalyzed by copper, palladium, or rhodium complexes (see Sects. 8.2, 8.7, and 8.8). There are cases where it is not clearly known whether route A or B is followed. Scheme 6-37 also includes... 

---