Demonstrate meaning

Figure 4. Ten bouts of high intensity cycle exercise, each with a duration of 6 sec and with 30 sec rest periods between bouts were performed on a given day. The entire exercise protocol was performed on four separate days by each subject (n = 8), before and after placebo and creatine supplementation. Mean power output was 882 watts. Upper panels (A1 and B1) demonstrate mean revolutions per min during the 0-4 sec period of each bout and the lower panel (A2 and B2) during 4-6 sec of each bout. The left panels (A1 and A2) show results before (o) and after (x) placebo and the right panels (B1 and B2) before (o) and after (x) creatine supplementation. The study was performed in a double blind manner.

Demonstration means the showing by actual use of equipment or procedures. 

These are not shown in the computationally easiest form. This form demonstrates meaning. 

This is the first time that OSHA has used the term demonstrate. In reality, demonstration means do as I do [3]. This is an important concept no matter what you are tying to accomplish—always walk the walk, and talk the talk. ... 

Once again, the demonstration means to find the object z from group. From the similarity of a with b and c, can be written the equality ... 

Figure 9.2 demonstrates mean velocity v = and efficiency as a function of the sperm number Sp. The reduced velocity v/ Im) in Figure 9.2a exhibits the same behavior as reported in Refs [51, 52], where the elastic filament is driven by an oscillating torque acting on one of its ends. For small sperm numbers around Sp = 3,... 

Harmonised standards are technical specifications adopted by one of the European standards organisations following a mandate issued by the European Commission on which Member States were consulted. When published by the Commission in the Official Journal of the European Communities, the hamionised standards give presumption of confomiity to the essential requirements they specify. This means that manufacturers applying these standards do not have to demonstrate the compliance of the manufactured products with the relevant requirements of the directive. 

Finally, under the heading Specific pressure equipment requirements specific requirements are set out for equipment with a risk of overheating, for piping and, last but not least, specific quantitative requirements which set out a series of safety factors for certain pressure equipment. These latter provisions apply as a general rule which means that a manufacturer or a harmonised standard may deviate from these factors if it can be demonstrated that appropriate measures have been taken to achieve an equivalent level of safety. 

Otlier lithographical means include micromachining [175], photopatteming [176] or electron beam patterning [1771, which have been demonstrated on alkanetliiolate/Au SAMs, alkanetliiolate and organo-siloxane on Si and Ti and alkanetliiolates on GaAs. 

This analysis is heuristic in the sense that the Hilbert spaces in question are in general of large, if not infinite, dimension while we have focused on spaces of dimension four or two. A form of degenerate perturbation theory [3] can be used to demonstrate that the preceding analysis is essentially correct and, to provide the means for locating and characterizing conical intersections. 

Determine the melting point of pure cinnamic acid (133°) and pure urea (133°). Intimately mix approximately equal weights (ca. 01 g.) of the two finely-powdered compounds and determine the melting point a considerable depression of melting point will be observed. Obtain an unknown substance from the demonstrator and, by means of a mixed melting point determination, discover whether it is identical with urea or cinnamic acid. 

As demonstrated in Problem 11, this integral reduces to 0.959. This means that the N2 v=0 state, subsequent to sudden ionization, can be represented as containing j0.959f = 0.92 fraction of the v=0 state of the ion. 

This eonstruetion in whieh a veetor is used to form a matrix v(i)Xv(i) is ealled an "outer produet". The projeetion matrix thus formed ean be shown to be idempotent. whieh means that the result of applying it twiee (or more times) is identieal to the result of applying it onee P P = P. This property is straightforward to demonstrate. Let us eonsider... 

In other cases, association has been demonstrated by means of phase diagrams of binary mixtures (158). 

Analytical chemistry has in recent years been equipped with a number of powerful means of investigation. Their application, especially that of gas-phase chromatography coupled with a mass spectrometer, has demonstrated the presence of a certain number of thiazoles in natural products such as fruits or cereals (287. 288, 297). The many results are shown in Table III-59. 

These procedures proposed by Dubinin and by Stoeckli arc, as yet, in the pioneer stage. Before they can be regarded as established as a means of evaluating pore size distribution, a wide-ranging study is needed, involving model micropore systems contained in a variety of chemical substances. The relationship between the structural constant B and the actual dimensions of the micropores, together with their distribution, would have to be demonstrated. The micropore volume would need to be evaluated independently from the known structure of the solid, or by the nonane pre-adsorption method, or with the aid of a range of molecular probes. 

In Table 5.3, is compared with the total hydroxyl concentration (Ni, + N ) of the corresponding fully hydroxylated, sample. The results clearly demonstrate that the physical adsorption is determined by the total hydroxyl content of the surface, showing the adsorption to be localized. It is useful to note that the BET monolayer capacity n JH2O) (= N ) of the water calculated from the water isotherm by the BET procedure corresponds to approximately 1 molecule of water per hydroxyl group, and so provides a convenient means of estimating the hydroxyl concentration on the surface. Since the adsorption is localized, n.(H20) does not, of course, denote a close-packed layer of water molecules. Indeed, the area occupied per molecule of water is determined by the structure of the silica, and is uJH2O) 20A ... 

---