Cracking, in zeolites

Lai et al. [30] prepared ZSM-5 zeolite membrane using a template (TPA+) free synthesis gel. In this way, calcinations, which often results in cracks in zeolite film, were unnecessary. Another advantage was that expensive and toxic templates were not applied in the synthesis gel, which made the preparation process more cost effective and environmentally friendly. 

Chromium zeolites are recognised to possess, at least at the laboratory scale, notable catalytic properties like in ethylene polymerization, oxidation of hydrocarbons, cracking of cumene, disproportionation of n-heptane, and thermolysis of H20 [ 1 ]. Several factors may have an effect on the catalytic activity of the chromium catalysts, such as the oxidation state, the structure (amorphous or crystalline, mono/di-chromate or polychromates, oxides, etc.) and the interaction of the chromium species with the support which depends essentially on the catalysts preparation method. They are ruled principally by several parameters such as the metal loading, the support characteristics, and the nature of the post-treatment (calcination, reduction, etc.). The nature of metal precursor is a parameter which can affect the predominance of chromium species in zeolite. In the case of solid-state exchange, the exchange process initially takes place at the solid- solid interface between the precursor salt and zeolite grains, and the success of the exchange depends on the type of interactions developed [2]. The aim of this work is to study the effect of the chromium precursor on the physicochemical properties of chromium loaded ZSM-5 catalysts and their catalytic performance in ethylene ammoxidation to acetonitrile. 

The analysis of the literature data shows that zeolites modified with nobel metals are among perspective catalysts for this process. The main drawbacks related to these catalysts are rather low efficiency and selectivity. The low efficiency is connected with intracrystalline diffusion limitations in zeolitic porous system. Thus, the effectiveness factor for transformation of n-alkanes over mordenite calculated basing on Thiele model pointed that only 30% of zeolitic pore system are involved in the catalytic reaction [1], On the other hand, lower selectivity in the case of longer alkanes is due to their easier cracking in comparison to shorter alkanes. 

The development of composite micro/mesoporous materials opens new perspectives for the improvement of zeolytic catalysts. These materials combine the advantages of both zeolites and mesoporous molecular sieves, in particular, strong acidity, high thermal and hydrothermal stability and improved diffusivity of bulky molecules due to reduction of the intracrystalline diffusion path length, resulting from creation of secondary mesoporous structure. It can be expected that the creation of secondary mesoporous structure in zeolitic crystals, on the one hand, will result in the improvement of the effectiveness factor in hydroisomerization process and, on the other hand, will lead to the decrease of the residence time of products and minimization of secondary reactions, such as cracking. This will result in an increase of both the conversion and the selectivity to isomerization products. 

A variety of solid acids besides zeolites have been tested as alkylation catalysts. Sulfated zirconia and related materials have drawn considerable attention because of what was initially thought to be their superacidic nature and their well-demonstrated ability to isomerize short linear alkanes at temperatures below 423 K. Corma et al. (188) compared sulfated zirconia and zeolite BEA at reaction temperatures of 273 and 323 K in isobutane/2-butene alkylation. While BEA catalyzed mainly dimerization at 273 K, the sulfated zirconia exhibited a high selectivity to TMPs. At 323 K, on the other hand, zeolite BEA produced more TMPs than sulfated zirconia, which under these conditions produced mainly cracked products with 65 wt% selectivity. The TMP/DMH ratio was always higher for the sulfated zirconia sample. These distinctive differences in the product distribution were attributed to the much stronger acid sites in sulfated zirconia than in zeolite BEA, but today one would question this suggestion because of evidence that the sulfated zirconia catalyst is not strongly acidic, being active for alkane isomerization because of a combination of acidic character and redox properties that help initiate hydrocarbon conversions (189). The time-on-stream behavior was more favorable for BEA, which deactivated at a lower rate than sulfated zirconia. Whether differences in the adsorption of the feed and product molecules influenced the performance was not discussed. 

Catalytic dewaxing, in which straight-chain paraffin hydrocarbons are selectively cracked on zeolite-type catalysts, and the lower-boiling reaction products are separated from the dewaxed lubricating oil by fractionation. 

Historically, the earliest C8 aromatic isomerization catalysts tended to use amorphous supports with a halogen such as chloride or fluoride. Due to water sensitivity and corrosion issues, these were replaced by large-pore zeolites such as mordenite. The larger pore size was more favorable toward bimolecular transalkylation, whereas the chlorided alumina support tended to promote cracking. In both... 

Venuto, P.B. and HaWb, E.T. (1979) Fluidized Catalytic Cracking with Zeolite Catalysts, Marcel Dekker, New York. Magee, J.S. and Mitchell, M.M. (1993) Fluid cataytic cracking science and technology, in Studies in Surface Science and Technology, vol. 75, Elsevier. 

Venuto, P. B. and Habib, E. T. in "Fluid Catalytic Cracking with Zeolite Catalysts," M. Dekker, Inc., 1979. 

Figure 1. Stylized site placement effects on cetane cracking in high Si/Al zeolites.

The Use of Rare Earth Elements in Zeolite Cracking Catalysts... 

Tphe rate-limiting processes in catalytic reaction over zeolites remain A largely undefined, mainly because of the lack of information on counterdiffusion rates at reaction conditions. Thomas and Barmby (7), Chen et al. (2, 3), and Nace (4) speculate on possible diffusional limitations in catalytic cracking over zeolites, and Katzer (5) has shown that intracrystalline diffusional limitations do not exist in liquid-phase benzene alkylation with propene. Tan and Fuller (6) propose internal mass transfer limitations and rapid fouling in benzene alkylation with cyclohexene over Y zeolite, based on the occurrence of a maximum in the reaction rate at about 100 min in flow reaction studies. Venuto et al (7, 8, 9) report similar rate maxima for vapor- and liquid-phase alkylation of benzene and dehydro-... 

---