Copolymers end-groups

Furthermore, size-exclusion chromatography (SEC) analyses generally reveal a bimodal distribution of molecular weights of the copolymers. Concomitantly, MALDI-ToF mass spectral measurements exhibit two sets of peaks corresponding to copolymer end groups of -OH and -X. For example, utilizing a (salen)CrCl/bis (triphenylphosphme)iminium chloride ([PPNjCl) catalyst for the copolymerization of cyclohexene oxide and carbon dioxide, the two copolymers illustrated in Fig. 6 were observed [26]. 

Scheme 8.1 Olefin-carbon monoxide copolymers end-groups and reactions responsible for their formation.

Polymer or copolymer End group Analysis method Comment... 

This book is intended to be a complete compendium of the types of methodology that have evolved for the determination of the chemical composition of polymers. The structure and microstructure of polymers, copolymers and rubbers are dealt with in Volume 2. More detailed aspects, such as sequencing of monomer emits in copolymers, end-group analysis, tacticity and stereochemcial determinations, will be dealt with in this subsequent volume. 

Polymer or Copolymer End-Group Method of Analysis Comments Ref. 

Note that the method of end group analysis is inapplicable to copolymers, since the presence of more than one repeat unit adds extra uncertainty as to the nature of chain ends. The above example included the remark that the molecular weights calculated in the example were average values. In the next section we shall examine this point in greater detail. 

Chemical Structure and Properties. Homopolymer consists exclusively of repeating oxymethylene units. The copolymer contains alkyhdene units (eg, ethyUdene —CH2—CH2—) randomly distributed along the chain. A variety of end groups may be present in the polymers. Both homopolymer and copolymer may have alkoxy, especially methoxy (CH3 O—), or formate (HCOO—) end groups. Copolymer made with ethylene oxide has 2-hydroxyethoxy end groups. Homopolymer generally has acetate end groups. 

The enthalpy of the copolymerization of trioxane is such that bulk polymerization is feasible. For production, molten trioxane, initiator, and comonomer are fed to the reactor a chain-transfer agent is in eluded if desired. Polymerization proceeds in bulk with precipitation of polymer and the reactor must supply enough shearing to continually break up the polymer bed, reduce particle size, and provide good heat transfer. The mixing requirements for the bulk polymerization of trioxane have been reviewed (22). Raw copolymer is obtained as fine emmb or flake containing imbibed formaldehyde and trioxane which are substantially removed in subsequent treatments which may be combined with removal of unstable end groups. 

Among the techniques employed to estimate the average molecular weight distribution of polymers are end-group analysis, dilute solution viscosity, reduction in vapor pressure, ebuUiometry, cryoscopy, vapor pressure osmometry, fractionation, hplc, phase distribution chromatography, field flow fractionation, and gel-permeation chromatography (gpc). For routine analysis of SBR polymers, gpc is widely accepted. Table 1 lists a number of physical properties of SBR (random) compared to natural mbber, solution polybutadiene, and SB block copolymer. 

Step-Growth Gopolymerization. A sample of a block copolymer prepared by condensation polymerisation is shown in equation 30 (37). In this process, a prepolymer diol (HO—Z—OH) is capped with isocyanate end groups and chain extended with a low molecular-weight diol (HO—E—OH) to give a so-called segmented block copolymer, containing polyurethane hard blocks and O—Z—O soft blocks. 

After brief discussion of the state-of-the-art of modern Py-GC/MS, some most recent applications for stixictural and compositional chai acterization of polymeric materials are described in detail. These include microstixictural studies on sequence distributions of copolymers, stereoregularity and end group chai acterization for various vinyl-type polymers such as polystyrene and polymethyl methacrylate by use of conventional analytical pyrolysis. 

Low molecular weight liquid nitrile rubbers with vinyl, carboxyl or mercaptan reactive end groups have been used with acrylic adhesives, epoxide resins and polyesters. Japanese workers have produced interesting butadiene-acrylonitrile alternating copolymers using Ziegler-Natta-type catalysts that are capable of some degree of ciystallisation. 

The stability of the copolymers may be enhanced by alkaline hydrolysis following polymerisation to remove oxymethyl end-groups and replace them with the more stable oxyethyl groups. 

The polymers initiated by BP amines were found to contain about one amino end group per molecular chain. It is reasonable to consider that the combination of BP and such polymers will initiate further polymerization of vinyl monomers. We investigated the photopolymerization of MMA with BP-PMMA bearing an anilino end group as the initiation system and found an increase of the molecular weight from GPC and viscometrical measurement [91]. This system can also initiate the photopolymerization of AN to form a block copolymer, which was characterized by GPC, elemental analysis, and IR spectra. The mechanism proposed is as follows ... 

Photoinitiators provide a convenient route for synthesizing vinyl polymers with a variety of different reactive end groups. Under suitable conditions, and in the presence of a vinyl monomer, a block AB or ABA copolymer can be produced which would otherwise be difficult or impossible to produce by another polymerization method. Moreover, synthesis of block copolymers by this route is much more versatile than those based on anionic polymerization, since a wider range of a monomers can be incorporated into the blocks. 

If (P ) is terminated by a chain transfer to a solvent or a monomer, a graft copolymer is formed, or, if the termination is from a combination, a crosslinked network polymer is formed. If the pre-existing polymer (B) contains an end group that itself is photosensitive (or can produce a radical by interacting with photoinitiator) and in the presence of a vinyl monomer (A), block copolymer of type AB can be produced if the photosensitive group is on one end of the polymeric chain. Type ABA block copolymer can be produced if the polymer chain (B) contains a photosensitive group on both ends. 

The quantum yield of polymerization is 6.72 and for photoinitiation < / = 2.85 x 10 . The polystyrene produced with this initiator shows photosensitivity when irradiated with UV light (A = 280 nm). This polymer, which carries two photosensitive end groups of - SC(S) N(CH3)2, behaves as a telechelic polymer and it is useful for production of ABA block copolymer. 

---