Cooling rubber

The gas rate must be so regulated that excessive quantities of S dust do not reach the vicinity of the cooled rubber stopper, or the tiflje will readily be plugged. The optimum flow rate is approximately eight liters/hour, in which case the yield is 75%. 

This is illustrated in Fig. 15, where the degree of crystallinity is expressed by the relative volume. It appears, that when super-cooling rubber so quickly that it remains amorphous, a greater volume is found than for slow cooling, the latter leading to a more complete crystallisation. The location of T , is not influenced by the crystallisation. The temperature at which crystallisation begins (T is at -h 10 C), is a kind of transition point, not identical with the brittle point T b, the latter being lower Perhaps it is identical with Tf the transition point gel —fluid, but this cannot be said with certainty as yet. 

A major problem in cooling rubber, in any process, is its inherently poor conductivity, which means that it is only cooled where it touches a cool surface. Thus, total heat removal depends on the area of the coohng surface and also on the way in which fresh rubber surfaces are moved into contact with that cooling surface. In internal mixers this depends mainly on the geometry of the rotors. Mixers with intermeshing rotors are less influenced by the friction or adhesion between the rubber and metal, and are, therefore, less sensitive to starting temperature. Rotor geometry also affects the overall heat transfer coefficient in a mixer. ... 

Assemble in a fume-cupboard the apparatus shown in Fig. 67(A). Place 15 g. of 3,5-dinitrobenzoic acid and 17 g. of phosphorus pentachloride in the flask C, and heat the mixture in an oil-bath for hours. Then reverse the condenser as shown in Fig. 67(B), but replace the calcium chloride tube by a tube leading to a water-pump, the neck of the reaction-flask C being closed with a rubber stopper. Now distil off the phosphorus oxychloride under reduced pressure by heating the flask C in an oil-bath initially at 25-30, increasing this temperature ultimately to 110°. Then cool the flask, when the crude 3,5-dinitro-benzoyl chloride will solidify to a brown crystalline mass. Yield, 16 g., i.e,y almost theoretical. Recrystallise from caibon tetrachloride. The chloride is obtained as colourless crystals, m.p. 66-68°, Yield, 13 g Further recrystallisation of small quantities can be performed using petrol (b.p. 40-60°). The chloride is stable almost indefinitely if kept in a calcium chloride desiccator. 

Fit securely to the lower end of the condenser (as a receiver) a Buchner flask, the side-tube carrying a piece of rubber tubing which falls well below the level of the bench. Steam-distil the ethereal mixture for about 30 minutes discard the distillate, which contains the ether, possibly a trace of unchanged ethyl benzoate, and also any biphenyl, CeHs CgHs, which has been formed. The residue in the flask contains the triphenyl carbinol, which solidifies when the liquid is cooled. Filter this residual product at the pump, wash the triphenyl-carbinol thoroughly with water, drain, and then dry by pressing between several layers of thick drying-paper. Yield of crude dry product, 8 g. The triphenyl-carbinol can be recrystallised from methylated spirit (yield, 6 g.), or, if quite dry, from benzene, and so obtained as colourless crystals, m.p. 162. ... 

Cool the flask in ice-water and pour the ethereal solution into a mixture of about 6 ml. of dil. H2SO4 and 10 g. of crushed ice contained in a 50 ml. flask fitted for steam-distillation, taking care to leave behind any unchanged magnesium. Fit to the lower end of the condenser a small Buchner flask or boiling-tube with side-arm (45°) carrying a piece of rubber tubing which falls well below the level of the bench. 

A 1500 ml. flask is fitted (preferably by means of a three-necked adaptor) with a rubber-sleeved or mercury-sealed stirrer (Fig. 20, p. 39), a reflux water-condenser, and a dropping-funnel cf. Fig. 23(c), p. 45, in which only a two-necked adaptor is shown or Fig. 23(G)). The dried zinc powder (20 g.) is placed in the flask, and a solution of 28 ml. of ethyl bromoacetate and 32 ml. of benzaldehyde in 40 ml. of dry benzene containing 5 ml. of dry ether is placed in the dropping-funnel. Approximately 10 ml. of this solution is run on to the zinc powder, and the mixture allowed to remain unstirred until (usually within a few minutes) a vigorous reaction occurs. (If no reaction occurs, warm the mixture on the water-bath until the reaction starts.) The stirrer is now started, and the rest of the solution allowed to run in drop-wise over a period of about 30 minutes so that the initial reaction is steadily maintained. The flask is then heated on a water-bath for 30 minutes with continuous stirring, and is then cooled in an ice-water bath. The well-stirred product is then hydrolysed by the addition of 120 ml. of 10% sulphuric acid. The mixture is transferred to a separating-funnel, the lower aqueous layer discarded, and the upper benzene layer then... 

Fit a three necked 250 ml. flask with a central rubber-sleeved or mercury-sealed stirrer, c/. Fig. 23(c), p. 45, where only two necks are shown, and with a thermometer the bulb of which reaches as near the bottom of the flask as the stirrer allows the third neck will carry at first a dropping-funnel and later a reflux condenser. Place 20 g. (19-5 ml.) of ethyl acetoacetate and 45 ml. of glacial acetic acid in the flask and by ice-water cooling adjust the temperature of the stirred mixture to 5 -7° maintain this temperature whilst adding a solution of 5 4 g. of sodium nitrite in 8 ml. of water slowly from the dropping-funnel during 15 minutes. Continue the stirring for 20-30 minutes, and then... 

Meanwhile, the organic compound can be prepared for analysis whilst the sealed end C (Fig. 72) of the Carius tube has been cooling dow n. For this purpose, thoroughly clean and dry a small tube, which is about 6 cm. long and 8-10 mm. w ide. Weigh it carefully, supporting it on the balance pan either by means of a small stand of aluminium foil, or by a short section of a perforated rubber stopper (Fig. 73 (A) and (B) respectively) alternatively the tube may be placed in a small beaker on the balance pan, or suspended above the pan by a small hooked wire girdle. 

The absorption tubes are then detached from each other, transferred to their stand, and polished, matured and weighed exactly as at the beginning of the experiment, taking care that no particles of rubber or wax are left in the side-arms. They must be repolished, matured and reweighed before they are used for a further determination. Finally when the tube is cool, the tap Tj of the purification train may be closed and the oxygen supply shut off. 

Mix 50 ml. of formalin, containing about 37 per cent, of formaldehyde, with 40 ml. of concentrated ammonia solution (sp. gr. 0- 88) in a 200 ml. round-bottomed flask. Insert a two-holed cork or rubber stopper carrying a capillary tube drawn out at the lower end (as for vacuum distillation) and reaching almost to the bottom of the flask, and also a short outlet tube connected through a filter flask to a water pump. Evaporate the contents of the flask as far as possible on a water bath under reduced pressure. Add a further 40 ml. of concentrated ammonia solution and repeat the evaporation. Attach a reflux condenser to the flask, add sufficient absolute ethyl alcohol (about 100 ml.) in small portions to dissolve most of the residue, heat under reflux for a few minutes and filter the hot alcoholic extract, preferably through a hot water fuimel (all flames in the vicinity must be extinguished). When cold, filter the hexamine, wash it with a little absolute alcohol, and dry in the air. The yield is 10 g. Treat the filtrate with an equal volume of dry ether and cool in ice. A fiulher 2 g. of hexamine is obtained. 

Dissolve 180 g. of commercial ammonium carbonate in 150 ml. of warm water (40-50°) in a 700 ml. flask. Cool to room temperature and add 200 ml. of concentrated ammonia solution (sp. gr. 0 88). Introduce slowly, with swirling of the contents of the flask, a solution of 50 g. of chloroacetic acid (Section 111,125) in 50 ml. of water [CAUTION do not allow chloroacetic acid to come into contact with the skin as unpleasant burns will result]. Close the flask with a solid rubber stopper and fix a thin copper wire to hold the stopper in place do not moisten the portion of the stopper in contact with the glass as this lubrication will cause the stopper to slide out of the flask. Allow the flask to stand for 24-48 hours at room temperature. Transfer the mixture to a distilling flask and distil in a closed apparatus until the volume is reduced to 100-110 ml. A convenient arrangement is to insert a drawn-out capillary tube into the flask, attach a Liebig s condenser, the lower end of which fits into a filter flask (compare Fig.//, 1) and connect the... 

---