Conversion factors weight

U.S. regulations define this standard as foUows proof spirit shaU be held to be that alcohoHc Hquor which contains one-half its volume of alcohol of a specific gravity of 0.7939 at 15.6°C ie, the figure for proof is always twice the percent alcohol content by volume. For example, 100° proof means 50% alcohol by volume. In the United Kingdom as weU as Canada, proof spirit is such that at 10.6°C alcohol weighs exactiy twelve-thirteenths of the weight of an equal bulk of distiUed water. A proof of 87.7° indicates an alcohol concentration of 50%. A conversion factor of 1.142 can be used to change British proof to U.S. proof. 

Corrosion Rate by CBD Somewhat similarly to the Tafel extrapolation method, the corrosion rate is found by intersecting the extrapolation of the linear poi tion of the second cathodic curve with the equihbrium stable corrosion potential. The intersection corrosion current is converted to a corrosion rate (mils penetration per year [mpy], 0.001 in/y) by use of a conversion factor (based upon Faraday s law, the electrochemical equivalent of the metal, its valence and gram atomic weight). For 13 alloys, this conversion factor ranges from 0.42 for nickel to 0.67 for Hastelloy B or C. For a qmck determination, 0.5 is used for most Fe, Cr, Ni, Mo, and Co alloy studies. Generally, the accuracy of the corrosion rate calculation is dependent upon the degree of linearity of the second cathodic curve when it is less than... 

Formulas, Molecular and Equivalent Weights, and Conversion Factors to CaCO, of Substances Frequently Appearing in the Chemistry of Water Softening... 

Specific volume is a conversion of specific gravity into cubic inches per pound. Since the volume of material in a product is the first bit of information established after its shape is formulated, the specific volume is a convenient conversion factor for weight ... 

Was a conversion factor used from ppm in food or water to a mg/bodv weight dose No. 

Was a conversion factor used from ppm in food or water to a mg/bodv weight dose Yes. A chronic food factor of 0.05 kg feed/kg body weight/day for rats was used to convert from ppm in food to mg/kg as follows 0.5 ppm x 0.05 = 0.025 mg/kg/day. (Data regarding body weight and food consumption were not available.) This is the food factor used in the original MRL derivation. 

The conversion factor, 1.995, corrects for the difference in molecular weight between acetochlor (269.77) and EMA (135.21). The conversion factor, 1.633, corrects for the difference in molecular weight between acetochlor (269.77) and MEMA (165.24). 

The conversion factor, 1.57, corrects for the difference in the molecular weight between propachlor (211.69) and NIPA (135.21). 

Quantitation is performed by the calibration technique. Construct a new calibration curve with methomyl oxime standard solutions (0.2, 0.4, 0.6, 0.8 and 1.0 xgmL in acetone) for each set of analyses. Plot the peak area against the injected amount of methomyl oxime on logarithmic paper. As the amount of alanycarb is measured in terms of its oxime derivative, a conversion factor of 3.8 (the molecular weight ratio of alanycarb to methomyl oxime) should be applied to obtain the net amount. The injection volume should be kept constant as the peak area varies with the injection volume in flame photometric detection. Before each set of measurements, check the GC system by injecting more than one standard solution containing ca 2-10 ng of methomyl oxime. 

Ans. There are 6.02 X 10 i atoms in 1.00 mol Na (Avogadro s number). There is 23.0 g of Na in LOO mol Na (equal to the atomic weight in grams). This problem requires use of two of the most important conversion factors involving moles. Note which one is used with masses and which one is used with numbers of atoms (or molecules of formula units). With numbers of atoms, molecules, or formula units, use Avogadro s number with mass or weight use the formula weight. 

In summary, for engineering systems both F and M can be considered fundamental because of the engineering definition of weight in addition to Newton s second law. However, this results in a redundancy, which needs to be recified by the conversion factor gc. The value of this conversion factor in the various engineering units provides the following identities ... 

It is seen that the diameters of bronchioles (averaged over generations 11 - 15) vary little with age. The increase in bronchial size is greater, but still less than might be expected if airways are simply scaled for overall body dimensions (illustrated by the dashed curves in Figure 9, which are functions of body weight W). Since bronchiolar diameter does not change much with age it is likely that the thickness of bronchiolar epithelium is also relatively constant. However, in the case of the bronchi, it is reasonable to assume that epithelial thickness is proportional to bronchial diameter. Thus, it is necessary to use age dependent conversion factors between the surface density of alpha-decays and dose to cells. 

Note Because there is a constant conversion factor between grams and pounds, we can work totally in pounds. Since the formula weights are CuFeS2 (183.5 g/mol), Cu2S (159.2 g/mol) and Cu (63.55 g/mol), we have... 

Conversion Factor 1 ppm = 7.79 mg/m3 at 77°F (based on average molecular weight) Human toxicity values have not been established or have not been published. 

Source of protein Proportion of nitrogen % total weight Conversion factor... 

---