Chemical reaction combustion

Combustion modeling capability. Combustion/ chemical reaction. Combustion/ chemical reaction Combustion/ chemical reaction Combustion/ chemical reaction Simple combustion/ Chemical reaction... 

When an ignition source is brought into contact with a flammable gas or mixture of gases, a combustion chemical reaction will occur at the point of introduction provided an oxidizer is present, normally oxygen. The combustion components are commonly referred to as a simple fire triangle ... 

A more scientific representation is a fire tetrahedron with the combustion chemical reaction considered as a fourth parameter or side of the tetrahedron. 

Heat - A form of thermal energy resulting from combustion, chemical reaction, friction, or movement of electricity. As a thermodynamic condition, heat, at a constant pressure, is equal to internal or intrinsic energy plus pressure times volume. 

Keywords Borghi diagram Combustion Chemical reactions Chemical kinetics Damkohler number Flamelets Ignition Karlovitz number Mixing-controlled... 

In this calculation, the molecular-weight ratio is obtained from the equation for the combustion chemical reaction, or CH4 + 2O2 = CO2 -I- 2H2O, that is, 16 -E 64 = 44 -I- 36, and C2H6 -I-72O2 = 2CO2 -E 3H2O, that is, 30 + 112 = 88 -E 54. 

The mass or volume heating value represents the quantity of energy released by a unit mass or volume of fuel during the chemical reaction for complete combustion producing CO2 and H2O. The fuel is taken to be, unless mentioned otherwise, at the liquid state and at a reference temperature, generally 25°C. The air and the combustion products are considered to be at this same temperature. 

Gas-phase reactions play a fundamental role in nature, for example atmospheric chemistry [1, 2, 3, 4 and 5] and interstellar chemistry [6], as well as in many teclmical processes, for example combustion and exliaust fiime cleansing [7, 8 and 9], Apart from such practical aspects the study of gas-phase reactions has provided the basis for our understanding of chemical reaction mechanisms on a microscopic level. The typically small particle densities in the gas phase mean that reactions occur in well defined elementary steps, usually not involving more than three particles. 

Optical metiiods, in both bulb and beam expermrents, have been employed to detemiine tlie relative populations of individual internal quantum states of products of chemical reactions. Most connnonly, such methods employ a transition to an excited electronic, rather than vibrational, level of tlie molecule. Molecular electronic transitions occur in the visible and ultraviolet, and detection of emission in these spectral regions can be accomplished much more sensitively than in the infrared, where vibrational transitions occur. In addition to their use in the study of collisional reaction dynamics, laser spectroscopic methods have been widely applied for the measurement of temperature and species concentrations in many different kinds of reaction media, including combustion media [31] and atmospheric chemistry [32]. 

Formation of Airborne Emissions. Airborne emissions are formed from combustion of waste fuels as a function of certain physical and chemical reactions and mechanisms. In grate-fired systems, particulate emissions result from particles being swept through the furnace and boiler in the gaseous combustion products, and from incomplete oxidation of the soHd particles, with consequent char carryover. If pile burning is used, eg, the mass bum units employed for unprocessed MSW, typically only 20—25% of the unbumed soHds and inerts exit the combustion system as flyash. If spreader-stoker technologies are employed, between 75 and 90% of the unbumed soHds and inerts may exit the combustion system in the form of flyash. 

Knock is caused by unwanted chemical reactions in the combustion chamber. These reactions are a function of the specific chemical species which make up the fuel and the environmental conditions to which the fuel is subjected during the compression and power stroke in the engine. Therefore, both the chemical makeup of the fuel and the engine design parameters must be considered when trying to understand knock. 

Vehicle Fa.ctors. Because knock is a chemical reaction, it is sensitive to temperature and reaction time. Temperature can in turn be affected either by external factors such as the wall temperature or by the amount of heat released in the combustion process itself, which is directiy related to the density of the fuel—air mixture. A vehicle factor which increases charge density, combustion chamber temperatures, or available reaction time promotes the tendency to knock. Engine operating and design factors which affect the tendency to produce knocking are... 

Chemical Reaction Measurements. Experimental studies of incineration kinetics have been described (37—39), where the waste species is generally introduced as a gas in a large excess of oxidant so that the oxidant concentration is constant, and the heat of reaction is negligible compared to the heat flux required to maintain the reacting mixture at temperature. The reaction is conducted in an externally heated reactor so that the temperature can be controlled to a known value and both oxidant concentration and temperature can be easily varied. The experimental reactor is generally a long tube of small diameter so that the residence time is well defined and axial dispersion may be neglected as a source of variation. Off-gas analysis is used to track both the disappearance of the feed material and the appearance and disappearance of any products of incomplete combustion. 

Some concerns directly related to a tomizer operation include inadequate mixing of Hquid and gas, incomplete droplet evaporation, hydrodynamic instabiHty, formation of nonuniform sprays, uneven deposition of Hquid particles on soHd surfaces, and drifting of small droplets. Other possible problems include difficulty in achieving ignition, poor combustion efficiency, and incorrect rates of evaporation, chemical reaction, solidification, or deposition. Atomizers must also provide the desired spray angle and pattern, penetration, concentration, and particle size distribution. In certain appHcations, they must handle high viscosity or non-Newtonian fluids, or provide extremely fine sprays for rapid cooling. 

---