Class III system

Of course it is also possible for a reaction system not to belong to any of these classes of approximate description.) Only in class III can equilibrium be said to be a special case of the steady-state treatment. Note that, for class III systems, the steady-state concentration of intermediate is very large,whereas for class I it is very small. Zuman and Patel have discussed the equilibrium and steady-state approximations in terms similar to the present treatment. 

It is a synthetic challenge for the inorganic coordination chemist to construct class III systems whose ground states have a significant... 

A dunk tank or attached decontamination air lock system may be used to introduce or remove material from the Class III system. Figure 8. All primary containment devices shall be certified to meet performance criteria on initial installation, following any move or maintenance, and at least annually. Other safety features of facility design include nonporous surfaces on floors, walls, and ceiling self-closing doors that must remain closed to maintain air balance and directional airflows. If floor drains are present, their traps should be filled with water weekly. 

In Class III systems, 2 Hab > and the electron is fully delocalized between the donor and acceptor. 

The energy of the optical transition in a symmetrical Class III system is given by... 

For a class III system (Figure lb), the value of /fad is given simply by... 

It has been often argued that in a mixed valence state of a pyrazine bridged dimer the appearance of a symmetric (pz) band at 1,580-1,590 cm provides evidence for valence localization (class II), while a fully delocalized class III system does not show the z symm(pz) band. In the present case, it was not possible to discuss the degree of delocalization based on the intensity of the symm(pz) band, because the acetate ligand (COO)asym bands obscure the z symm(pz) band. Meyer and co-workers pointed out the difficulty in the discrimination between localization and delocalization from the presence or the absence of symm(pz). ... 

As an example, results recently obtained by Scheidgen [68,69] for the system CO2 (A) -f 1-octanol (B) -f hexadecane (C) are given in Figs. 9 to 12. In Fig. 9, the p T) projections of the binary critical curves of CO2 + hexadecane (see also Fig. 5) and CO2 + 1-octanol are presented. They nearly coincide and run through pressure minima both have to be attributed to class-III systems. 

ELECTRIC POWER SYSTEM Clas I,II and III Electnc System CSAB290 5 The Class III system pow ers designated safety -related and economic equipm i protection loads pump motors, valv es etc) Normally Class IV power supplies the Class III power W. cn the Class IV system fails two redundant standby diesel generators provide Class ni power The ac Class II and dc Class I systems supply un-mtermptible power to the control and safety svstems... 

Class III Class III system is normally fed from Class IV system. But, when supply... 

M"-M but have some new properties that can be attributed to the mixed-valence species. Class II compounds typically have IT transitions that can be characterized using the Hush theory. Class III systems are compounds that have such strong electronic communication between the metal centers that they are completely delocalized systems. The oxidation state of the metal centers in a class ni system can best be described as Class III complexes typically do... 

There is some debate as to whether the localized- or trapped-valence description of the Taube-Creutz ion is correct or whether a delocalized picture is more appropriate. A theoretical study indicates that it is a delocalized, Class III system." Meyer and co-workers have summarized the structural and spectroscopic evidence and placed it between Class II and Class III. The trapped-valence model seems correct" for the complex in which the bridging ligand is 4,4 -bipyridine, since the two pyridine rings are not planar and therefore are not in 11 conjugation. 

The answer has two parts it s not needed and wasn t considered. First, almost without exception the SA cosolvent in a Class III cosolvent process will have low volatility so parts can be heated to a high temperature and so there is no concern about flammability, and often the RA cosolvent will be a volatile fluorinated material without a measured flash point so there is also no concern about flammability. Second, when this author created the classification scheme in the early 1990s, the focus was on Class II systems and the author did not adequately give Class III systems due consideration. 

---