Carbonation repairs

Most proprietary, pre-bagged mixes carry guarantees of the materials particularly for carbonation repairs. Manufacturers and applicators will be more cautious with chloride repairs and cannot guarantee that all chloride is removed in areas adjacent to the patch. The incipient anode problem (see Section 6.2.1) is far more prevalent in chloride contaminated structures so corrosion will continue around the patches. 

The rest of this section will discuss the options of patching and coating, realkalization and inhibitor application for carbonation repairs. 

The amount of patch repairing necessary and its underestimation are discussed in the previous section and above under carbonation repairs. 

Additional operations essential to commercial bauxite processing are steam and power generation, heat recovery to minimise energy consumption, process liquor evaporation to maintain a water balance, impurity removal from process liquor streams, classification and washing of ttihydrate, lime caustication of sodium carbonate [497-19-8] to sodium hydroxide [1310-73-2] repair and maintenance of equipment, rehabiUtation of mine and residue disposal sites, and quaUty and process control. Each operation in the process can be carried out in a variety of ways depending upon bauxite properties and optimum economic tradeoffs. 

Lead and Alloys Chemical leads of 99.9+ percent purity are used primarily in the chemical industiy in environments that form thin, insoluble, and self-repairable protective films, for example, salts such as sulfates, carbonates, or phosphates. More soluble films such as nitrates, acetates, or chlorides offer little protection. 

A diagnosis of possible damage should be made before beginning repairs with other construction measures [48,49]. There should be a checklist [48] of the important corrosion parameters and the types of corrosion effects to be expected. Of special importance are investigations of the quality of the concrete (strength, type of cement, water/cement ratio, cement content), the depth of carbonization, concentration profile of chloride ions, moisture distribution, and the situation regarding cracks and displacements. The extent of corrosion attack is determined visually. Later the likelihood of corrosion can be assessed using the above data. 

There are different concrete replacement systems available for renovating reinforced concrete structures. They range from sprayed concrete without polymer additions to systems containing conducting polymers (PCC-mortar). Since with the latter alkalinity is lower, more rapid carbonization occurs on weathering [59] and the increased electrical resistivity has to be taken into account, so that with cathodic protection only sprayed concrete should be used as a repair mortar. 

Maintenance and production records, along with the used lean and rich glycol analyses, can be very helpful to the troubleshooter. A history of filter element, carbon, tower packing, and firetube changeouts can sometimes be very revealing. The frequency of pump repairs and chemical cleaning jobs is also beneficial. With this type of knowledge, the troubleshooter can quickly eliminate and prevent costly problems. 

Welding is sometimes used to repair broken and defective castings [6]. This process is more difficult than welding steel because the high carbon content in cast iron may lead to brittle structures on cooling, thus... 

In dry air the stability of zinc is remarkable. Once the protective layer of zinc oxide formed initially is complete, the attack ceases. Even under under normal urban conditions, such as those in London, zinc sheet 0 -8 mm thick has been found to have an effective life of 40 years or more when used as a roof covering and no repair has been needed except for mechanical damage. The presence of water does, of course, increase the rate of corrosion when water is present the initial corrosion product is zinc hydroxide, which is then converted by the action of carbon dioxide to a basic zinc carbonate, probably of composition similar to ZnCOj 3Zn(OH)2 . In very damp conditions unprotected zinc sometimes forms a loose and more conspicuous form of corrosion product known as wet storage stain or white rust (see p. 4.171). 

Steel may have some merit SSCC of weld repairs in well-head alloys was investigated by Watkins and Rosenberg who found that the repairs were susceptible to this problem because of the hard HAZs developed by welding. Post-weld heat treatment was an essential but not complete cure compared with unrepaired castings. In the case of hydrogen-assisted cracking of welded structural steels, composition is more important than mechanical properties and the carbon equivalent should be... 

P-6 4 4 2 2 3 3 4 4 Easily machinable. Welds, repairs wen. Low carbon steel - not dimensionally stable in heal treatment. 

Figure 5.10. Defects consisting of oxygen vacancies constitute adsorption sites on a Ti02 (110) surface. Note how CO binds with its lone-pair electrons on a Ti ion (a Lewis acid site). O2 dissociating on a defect furnishes an O atom that locally repairs the defect. CO2 may adsorb by coordinating to an O atom, thus forming a carbonate group. [Figure adapted from W. Gopel, C. Rocher and R. Feierabend, Phys. Rev. B 28 (1983) 3427.]...

Hydroxyurea is an oral drug that inhibits ribonucleotide reductase, which converts ribonucleotides into the deoxyribuon-cleotides used in DNA synthesis and repair. The time to peak concentrations of hydroxyurea is 1 to 2 hours after oral administration. Approximately 50% is degraded by the liver to form urea and respiratory carbon dioxide. The remainder is excreted by the kidney. The half-life ranges from 3.5 to 4.5 hours. Hydroxyurea has shown clinical activity in the treatment of chronic myelocytic leukemia, polycythemia vera, and thrombocytosis. The major side effects are myelo-suppression, nausea and vomiting, diarrhea, and constipation. Rash, mucositis, and renal tubular dysfunction occur rarely. 

---