Bulk cleaning

The cleaning process proceeds by one of three primary mechanisms solubilization, emulsification, and roll-up [229]. In solubilization the oily phase partitions into surfactant micelles that desorb from the solid surface and diffuse into the bulk. As mentioned above, there is a body of theoretical work on solubilization [146, 147] and numerous experimental studies by a variety of spectroscopic techniques [143-145,230]. Emulsification involves the formation and removal of an emulsion at the oil-water interface the removal step may involve hydrodynamic as well as surface chemical forces. Emulsion formation is covered in Chapter XIV. In roll-up the surfactant reduces the contact angle of the liquid soil or the surface free energy of a solid particle aiding its detachment and subsequent removal by hydrodynamic forces. Adam and Stevenson s beautiful photographs illustrate roll-up of lanoline on wood fibers [231]. In order to achieve roll-up, one requires the surface free energies for soil detachment illustrated in Fig. XIII-14 to obey... 

Some fascinating effects occur in the case of CO on Pt(lOO). As illustrated in Fig. XVI-8, the clean surface is reconstructed naturally into a quasi-hexag-onal pattern, but on adsorption of CO, this reconstruction is lifted to give the bulk termination structure of (110) planes [56]. As discussed in Section XVIII-9E very complicated changes in surface structure occur on the oxidation of CO... 

Surfaces are found to exliibit properties that are different from those of the bulk material. In the bulk, each atom is bonded to other atoms m all tliree dimensions. In fact, it is this infinite periodicity in tliree dimensions that gives rise to the power of condensed matter physics. At a surface, however, the tliree-dimensional periodicity is broken. This causes the surface atoms to respond to this change in their local enviromnent by adjusting tiieir geometric and electronic structures. The physics and chemistry of clean surfaces is discussed in section Al.7.2. 

When atoms, molecules, or molecular fragments adsorb onto a single-crystal surface, they often arrange themselves into an ordered pattern. Generally, the size of the adsorbate-induced two-dimensional surface unit cell is larger than that of the clean surface. The same nomenclature is used to describe the surface unit cell of an adsorbate system as is used to describe a reconstructed surface, i.e. the synmietry is given with respect to the bulk tenninated (unreconstructed) two-dimensional surface unit cell. 

Surface crystallography started in the late 1960s, with the simplest possible structures being solved by LEED [14]. Such structures were the clean Ni (111), Cu(l 11) and Al(l 11) surfaces, which are unreconstructed and essentially unrelaxed, i.e. very close to the ideal temrination of the bulk shown in figure B 1.211 a) typically, only one unknown structural parameter was fitted to experiment, namely the spacing between the two outennost atomic layers. 

Extended defects range from well characterized dislocations to grain boundaries, interfaces, stacking faults, etch pits, D-defects, misfit dislocations (common in epitaxial growth), blisters induced by H or He implantation etc. Microscopic studies of such defects are very difficult, and crystal growers use years of experience and trial-and-error teclmiques to avoid or control them. Some extended defects can change in unpredictable ways upon heat treatments. Others become gettering centres for transition metals, a phenomenon which can be desirable or not, but is always difficult to control. Extended defects are sometimes cleverly used. For example, the smart-cut process relies on the controlled implantation of H followed by heat treatments to create blisters. This allows a thin layer of clean material to be lifted from a bulk wafer [261. 

Polypropylene fibers are used in every aspect of carpet constmetion from face fiber to primary and secondary backings. Polypropylene s advantages over jute as carpet backing are dimensional stabiUty and minimal moisture absorption. Drawbacks include difficulty in dyeing and higher cost. Bulked-continuous-filament (BCF) carpet yams provide face fiber with improved crimp and elasticity. BCF carpet yams are especially important in contract carpets, characterized by low dense loops, where easy cleaning is an advantage. 

The carbon black (soot) produced in the partial combustion and electrical discharge processes is of rather small particle si2e and contains substantial amounts of higher (mostly aromatic) hydrocarbons which may render it hydrophobic, sticky, and difficult to remove by filtration. Electrostatic units, combined with water scmbbers, moving coke beds, and bag filters, are used for the removal of soot. The recovery is illustrated by the BASF separation and purification system (23). The bulk of the carbon in the reactor effluent is removed by a water scmbber (quencher). Residual carbon clean-up is by electrostatic filtering in the case of methane feedstock, and by coke particles if the feed is naphtha. Carbon in the quench water is concentrated by flotation, then burned. 

Natural gas contains both organic and inorganic sulfur compounds that must be removed to protect both the reforming and downstream methanol synthesis catalysts. Hydrodesulfurization across a cobalt or nickel molybdenum—zinc oxide fixed-bed sequence is the basis for an effective purification system. For high levels of sulfur, bulk removal in a Hquid absorption—stripping system followed by fixed-bed residual clean-up is more practical (see Sulfur REMOVAL AND RECOVERY). Chlorides and mercury may also be found in natural gas, particularly from offshore reservoirs. These poisons can be removed by activated alumina or carbon beds. 

Important features of bulk milk tanks include a measuring device, generally a caUbrated rod or meter cleaning and sanitizing facdities and stirring with an appropriate agitator to cool and maintain cool milk temperatures. 

Carbon dioxide is used to increase the natural CO2 content of the beer and as counterpressure in tanks and filling machines. It must be free of water and any aroma. The consumption is 0—10 g/L of beer produced. In major breweries, carbon dioxide is bought in bulk, and in many breweries it is common practice to coUect the surplus CO2 from the fermentors to clean, dehumidify, and compress in a local CO2 plant which is easily automated. 

Polystyrene. Polystyrene [9003-53-6] is a thermoplastic prepared by the polymerization of styrene, primarily the suspension or bulk processes. Polystyrene is a linear polymer that is atactic, amorphous, inert to acids and alkahes, but attacked by aromatic solvents and chlorinated hydrocarbons such as dry cleaning fluids. It is clear but yellows and crazes on outdoor exposure when attacked by uv light. It is britde and does not accept plasticizers, though mbber can be compounded with it to raise the impact strength, ie, high impact polystyrene (HIPS). Its principal use in building products is as a foamed plastic (see Eoamed plastics). The foams are used for interior trim, door and window frames, cabinetry, and, in the low density expanded form, for insulation (see Styrene plastics). 

---