Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Boxing method

For the given orbital oeeupations (eonfigurations) of the following systems, determine all possible states (all possible allowed eombinations of spin and spaee states). There is no need to form the determinental wavefunetions simply label eaeh state with its proper term symbol. One method eommonly used is Harry Grays "box method" found in Eleetrons and Chemical Bonding. [Pg.316]

Often the inlet device (air supply) in a ventilated room is geometrically complicated. To resolve the flow around such a device would require a very fine grid. Instead of trying to resolve the complex flow near the inlet device, one can choose to use the box method or the prescribed velocity method.Both methods are based on the observation that downstream of the inlet, the flow behaves like a wall jet. Thus it is important that the bound-... [Pg.1042]

Nielsen, P. V. The box method—A practical procedure for introduction of an air terminal device in CFD calculation. Report R9744, Dept, of Building Technology and Structural Engineering, Aalborg University, Aalborg, 1997. [Pg.1057]

If the one-point calibration in ambient air is not sufficient, the next best approach is to use the calibration box method.- The air state is created in a closed box made of nonhygroscopic material, like metal or plastic. A controlled state of humidity is maintained by exposing the air in the box to a liquid surface of a saturated salt solution. In practice, a dish containing the saturated water solution of a salt is placed on supports at the bottom of the box. The air in the box is circulated by means of a small fan. The box should be airtight and positioned in a constant temperature environment. The calibrated instruments are placed in the box. A dewpoint hygrometer can be used as a reference. A wide range of humidity can be created by using solutions of different salts. Table 12.5 shows a few examples of equilibrium humidities achieved with different salt solutions. [Pg.1145]

The low value of 1.0 in Table VII for the rigid Polyurethane foam in the box-methods may be explained by low ventilation rate. The experiment is over in less than 1 minute and most of the material is combusted during that period. The ventilation rate becomes to low to generate a "normal" ratio of C02/C0 for fast burning materials. In this particular case the oxygen concentration become very close to 0 oxygen. [Pg.45]

It was Witt s criticism of the method of collecting turpentine from pine trees in the American South that stimulate Herty s interest in this subject. Upon returning to the United States in 1901, he turned his attention to this problem, and he soon developed his cup and gutter system, which replaced the old "boxing" method. Herty resigned his university post and worked with the United States Bureau of Forestry (1902-1904) and later the Chattanooga Pottery Company (1904-1905) in following up on his invention, which made him financially secure. [Pg.99]

Of the methods listed above, only the noniterative CC approaches based on the partitioning of the similarity-transformed Hamiltonian (24-28) and the (C)R-CC approaches of refs 9,13-18,20,21, which employ the MMCC formalism (P. 13, 14, 18, 19, 21, 45, 106, 107), retain the simplicity and the black-box character of the standard CCSD(T) or CCSD(TQf) methods. One of the two goals of the present work is the development of a new class of the MMCC-based black-box methods for multiple bond breaking. [Pg.39]

Thus, unlike the non-equivalent 2p13p1 case, in which 3p, Ip, - D, D, S, and S levels arise, only the 3p, Id, and S arise in the p2 situation. This "box method" is necessary to carry out whenever one is dealing with equivalent angular momenta. [Pg.186]

An adaptation of the Box method, however, seems to offer the advantage of improved efficiency while still being susceptible to automatic computation. Box s approach may be divided into two stages. The first, to which he has applied the name method of steepest ascents, is primarily for the purpose of approximately locating the optimum response. The second is a more intensive investigation in the local region of the optimum. This will permit a precise determination of the optimum and also indicate the behavior of the response in its neighborhood. [Pg.360]

Zoom Mode Two options are available for zooming your 2D spectrum. Normal allows zooming using the standard rubber box method while Units uses predefined increments. [Pg.132]

BS 874-3.1, 1987. Methods for determining thermal insulating properties. Tests for thermal transmittance and conductance. Guarded hot box method. [Pg.285]

White, P. A. F., and S. E. Smith, 1962, Inert Atmospheres. Butterworth, London. This book presents an excellent discussion of the purification of glove box atmospheres, and a good overview of glove box methods as practiced in the United Kingdom atomic energy establishments. Still lhc best general reference in the field. [Pg.208]

FDM was applied to electrochemical problems very early [4], but it was in the 1960s when Feldberg developed the basis of digital simulation of electrochemical processes by means of the box method, which at present is considered as a FEM-like method (see [5]). [Pg.648]

Sorption coefficients also have been determined from the motion of an unconfined sor-bate plume in a simulated aquifer box model. MacIntyre et al. (1991) compared the sorption coefficients for naphthalene on low soil organic carbon (less than 0.1%) aquifer materials determined by the batch, column, and box methods, and found good agreement among the three methods. [Pg.166]

MacIntyre, W.G., T.B. Stauffer, and C.P. Antworth. 1991. A comparison of sorption coefficients determined by batch, column, and box methods on a low organic carbon aquifer material. Ground Water 29(6) 908-913. [Pg.205]

Other methods that have been used to determine Koc values are the so-called box method (Macintyre et al., 1991), the continuous stirred reactor method (de Jonge et al., 1999) and headspace methods, which are especially useful for volatile chemicals (Garbarini and Lion, 1985). Delle Site (2001) has recently reviewed the available methods for the determination of Koc values. [Pg.362]

Many methods for the fitting of data obtained from pulsed NMR have been described in the literature. The methods may, for example, be classified as either time domain (TD) or FD methods. Alternatively, they may be described as black-box methods or as interactive methods. An excellent review is given by de Beer and van Ormondt.20 There is now a consensus21 that FD and TD fitting methods are equivalent in terms of y2 parameter estimation if potential artifacts introduced by Fourier transformation are handled properly. TD and FD fitting can truly be equivalent (i.e. same 2 minima) if 2 is determined over the whole data range (a consequence of the power theorem on the Fourier transform) and if the model used to fit the experimental spectrum is correct. Very often, however, the model used is only an approximation. [Pg.64]

Equation (2.2) is the only equation needed when using the box method and this is sometimes cited as an advantage. It brings one close to the microscopic system, as we shall see, and has - in theory - great flexibility in cases where the diffusion volume has an awkward geometry. In practice, however, most geometries encountered will be - or can be simplified to - one of but a few... [Pg.7]

A stretched stack of boxes was used by Feldberg [231] for the box-method, to be described in Chap. 9. Pao and Dougherty [433] developed the same idea... [Pg.107]


See other pages where Boxing method is mentioned: [Pg.251]    [Pg.254]    [Pg.261]    [Pg.1037]    [Pg.1042]    [Pg.1043]    [Pg.1180]    [Pg.122]    [Pg.130]    [Pg.45]    [Pg.274]    [Pg.187]    [Pg.183]    [Pg.193]    [Pg.86]    [Pg.101]    [Pg.102]    [Pg.104]    [Pg.193]    [Pg.470]    [Pg.257]    [Pg.3]    [Pg.145]    [Pg.145]    [Pg.147]    [Pg.148]   
See also in sourсe #XX -- [ Pg.104 ]




SEARCH



Box method

Box method

Box-Counting method

Box-Wilson optimization method

Particle in a box and variation method

The box method

Tool-box of methods

Variation method applied to particle in a box

© 2024 chempedia.info