Boron trifluoride etherate-Sodium borohydride

Any of these BH3 compounds adds readily to most alkenes at room temperature or lower temperatures. The reactions usually are carried out in ether solvents, although hydrocarbon solvents can be used with the borane-dimethyl sulfide complex. When diborane is the reagent, it can be generated either in situ or externally through the reaction of boron trifluoride with sodium borohydride ... 

A 500-ml three-necked flask is fitted with a dropping funnel, a condenser, and a magnetic stirrer. The flask is charged with a mixture of 3.4 g (0.09 mole) of powdered sodium borohydride, 150 ml of THF, and 25.2 g (0.30 mole) of 4-methyI-I-pentene. A solution of 15.1 ml (17.0 g, 0.12 mole) of boron trifluoride etherate in 20 ml of THF is added over a period of 1 hour, the temperature being maintained at 25° (water bath). The flask is stirred an additional hour at 25° and the excess hydride is decomposed with water (10 ml). 

The sodium borohydride solution is added dropwise to the stirred boron trifluoride etherate-diglyme solution resulting in the formation of diborane. The gas is swept into the olefin-TH F solution (held at 20°) by maintaining a slow flow of dry nitrogen through the generator. 

Although the synthesis of multiple-pyrrolyl compounds can be achieved by SnAt reactions of perfluoroaromatics with pyrrolylsodium at ambient temperature <96JOC9012>, deleterious side reactions are often observed during attempted A-alkylations of the alkali salts of pyrrole. A protocol has therefore been developed for the preparation of N-arylmethylenepyrroles by reduction of the corresponding AT-acyl derivatives by treatment with sodium borohydride/boron trifluoride etherate in a sealed tube <96S457>. ... 

Sodium borohydride does not reduce the free carboxylic group, but borane prepared from sodium borohydride and boron trifluoride etherate in tetrahydrofuran converts aliphatic acids to alcohols at 0-25° in 89-100% yields... 

Reduction of aromatic carboxylic acids to alcohols can be achieved by hydrides and complex hydrides, e.g. lithium aluminum hydride 968], sodium aluminum hydride [55] and sodium bis 2-methoxyethoxy)aluminum hydride [544, 969, 970], and with borane (diborane) [976] prepared from sodium borohydride and boron trifluoride etherate [971, 977] or aluminum chloride [755, 975] in diglyme. Sodium borohydride alone does not reduce free carboxylic acids. Anthranilic acid was reduced to the corresponding alcohol by electroreduction in sulfuric acid at 20-30° in 69-78% yield [979],... 

Borane-Sodium borohydride, 42 Borane-Tetrahydrofuran, 42 Boron tribromide, 43 Boron trichloride, 43 Boron trifluoride, 44 Boron trifluoride etherate, 3, 6, 10, 13, 43, 82, 99, 193, 200, 211, 306, 308, 321, 322... 

Sodium borohydride-Ace tic acid, 278 Sodium borohydride-Boron trifluoride etherate, 42... 

Sodium triacetoxyborohydride, 283 Tetrabutylammonium iodide-Boron trifluoride etherate, 287 Tributylborane, 325 Tributyl borate, 326 Triethylborane, 33, 292 Trimethyl borate, 218 Zinc borohydride, 167 Chromium Compounds Arene(tricarbonyl)chromium complexes, 19... 

Borane can be prepared in situ as described in Expts 5.44 and 5.89. Alternatively, a separate solution of borane in tetrahydrofuran can be prepared by adding a solution of sodium borohydride to boron trifluoride-etherate and sweeping the resulting borane into tetrahydrofuran with the aid of a nitrogen gas stream. 

This borane reagent may be prepared as follows.6 In a dry 500-ml flask equipped with a condenser, a thermometer and a pressure-equalising dropping funnel are placed 80 ml of diglyme, 23.1 g of 2-methylbut-2-ene (0.33 mol) in 20ml of diglyme and 4.7 g of sodium borohydride (0.125 mol). The flask is immersed in an ice bath and 23.5 g of boron trifluoride-etherate (0.165 mol) is added dropwise over a period of 30 minutes. The semi-solid reaction mixture containing 0.165 mol of disiamylborane is permitted to remain an additional 15 hours at 0-5 °C, and then used for hydroboration. Examples of the use of disiamylborane are described in Sections 5.4.3 p. 542 and 5.7.1, p. 588. 

We also found that ester functionality was compatible with this reduction sequence. Thus, treatment of the ester-lactone 81 with sodium borohydride and boron trifluoride etherate provided the tetrahydropyran 123 in 55% purified yield. Upon reaction with sodium hydroxide, 81 underwent simple ester hydrolysis to furnish the carboxylic acid 127 (see Table 3). 

Chlorosulfonic acid Thionyl chloride Sodium borohydride Boron trifluoride etherate Maleic acid Carbon (Darco KB)... 

In a similar way, O-methylflavinantinol (59) rearranges under the action of boron trifluoride etherate to give, via the neospirinedienone 60, the iminium salt 61, whose catalytic reduction produces laurifonine (4) in excellent overall yield (55) (Scheme 15). Laurifonine (4) has also been obtained by TFA-promoted dienol-benzene rearrangement of 59 followed by reduction with sodium borohydride 24). 

The reduction can also be achieved by utilizing in situ generated BHj THF (from sodium borohydride and boron trifluoride etherate). The scope of this reaction includes the synthesis of novel 3-chroman-amine derivatives (60 equation 33). This stereoselective reaction proceeds via the hydroxylamine intermediate only c/s-2-aryl-3-amino derivatives are obtained. 

Borane, which is used as a complex with tetrahydrofuran [992] or dimethyl sulfide [611, 992] or generated in situ from lithium borohydride with boron trifluoride etherate [646] or sodium borohydride with aluminum chloride [184], reacts with 3 mol of an alkene to form a tertiary borane. The oxidation with alkaline hydrogen peroxide [183, 992, 1201] or with trimethylamine oxide [991, 992] yields an alcohol (equations 598 and 599). 

---