Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Bonding and grounding

The voltage difference between two conductive materials is reduced to zero by bonding the two materials, that is, by bonding one end of a conducting wire to one of the materials and bonding the other end to the second material. [Pg.332]

When comparing sets of bonded materials, the sets may have different voltages. The voltage difference between sets is reduced to zero by bonding each set to ground, that is, by grounding. [Pg.332]

9 API RP 2003, Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents (Washington, DC American Petroleum Institute, 1991). [Pg.332]

Protect against the accumulation of electrostatic charges which can cause ignition. This may include the bonding and grounding of the tank, piping. [Pg.45]

Provide damper mechanical position stop to prevent complete closure of damper Eliminate ignition sources within the ductwork Use bonding and grounding Eliminate flammables or combustible by material substitution Use inert atmosphere... [Pg.50]

Provide adequate bonding and grounding Use ant-static drive belt... [Pg.67]

Install appropriate bonding and grounding with periodic testing... [Pg.83]

Implement procedure for manual bonding and grounding of tools to filter box... [Pg.102]

Conductive objects may accumulate charge via conduction, induction, ion collection or contact-separation in relation to a nonconductor. In general, charge accumulation on conductive objects can be completely prevented by bonding and grounding. The only decisions to be made are how small the resistance to ground must be (4-1.3) and how small a conductive object needs to be before it can be neglected. The latter depends on the results of... [Pg.48]

The 23 line drawings in [130] are very helpful for most routine bonding and grounding applications and for many years have been reproduced in NPCA 803 [6j. The following two sections cover general nonroutine applications. Chapters 5 and 6 of this book address specific grounding applications and special cases where electrical continuity may be unexpectedly lost. [Pg.73]

These do not pose a recognized static hazard if the curtain device and all equipment that could be electrically charged during operation is bonded and grounded [45,46]. [Pg.158]

Mixers and agitators designed for flammable liquids or dusts should be constructed to minimize fire and explosive possibilities. Electrical equipment should follow the requirements of Uie National Electrical Code. Equipment should be bonded and grounded to prevent Uie accumulation of staUc electricity. [Pg.494]

Figure 7-18 Bonding and grounding procedures for tanks and vessels. Adapted from F. G. Eichel, Electrostatics, Chemical Engineering (Mar. 13, 1967), p. 153. Figure 7-18 Bonding and grounding procedures for tanks and vessels. Adapted from F. G. Eichel, Electrostatics, Chemical Engineering (Mar. 13, 1967), p. 153.
Solids are transferred safely by bonding and grounding all conductive parts and/or by using nonconductive parts (drum and chute). See Figure 7-22. [Pg.337]

What bonding and grounding procedures must be followed to transfer a drum of flammable solvent into a storage tank ... [Pg.348]

See other pages where Bonding and grounding is mentioned: [Pg.497]    [Pg.2332]    [Pg.2333]    [Pg.42]    [Pg.49]    [Pg.70]    [Pg.83]    [Pg.100]    [Pg.116]    [Pg.138]    [Pg.162]    [Pg.49]    [Pg.71]    [Pg.71]    [Pg.73]    [Pg.74]    [Pg.106]    [Pg.128]    [Pg.130]    [Pg.131]    [Pg.157]    [Pg.185]    [Pg.190]    [Pg.195]    [Pg.198]    [Pg.203]    [Pg.217]    [Pg.516]    [Pg.189]    [Pg.857]    [Pg.859]    [Pg.564]    [Pg.332]    [Pg.332]    [Pg.348]   
See also in sourсe #XX -- [ Pg.332 , Pg.333 , Pg.334 ]

See also in sourсe #XX -- [ Pg.71 , Pg.72 , Pg.73 , Pg.74 ]

See also in sourсe #XX -- [ Pg.239 ]



SEARCH



Covalent Bonding in Ground and Excited States

Grounding and Bonding of Electrical Equipment

© 2024 chempedia.info