Base indicators

The colorations produced in this reaction arise from the action of nitrous acid on the phenol, giving />-nitrosophenol (I) which then reacts with excess of phenol to form an indophenol (II) which is an acid-base indicator ... 

H H Acid-base indicator recommended for titration of acids... 

Name pH Range Color Change Acid to Base Indicator Solution... 

Use acid-base indicator solutions. Oxidation causes bleaching of indicator to colorless... 

Harvey, D. T. Statistical Evaluation of Acid/Base Indicators, /. Chem. Educ. 1991, 68, 329-331. 

Standardization—External standards, standard additions, and internal standards are a common feature of many quantitative analyses. Suggested experiments using these standardization methods are found in later chapters. A good project experiment for introducing external standardization, standard additions, and the importance of the sample s matrix is to explore the effect of pH on the quantitative analysis of an acid-base indicator. Using bromothymol blue as an example, external standards can be prepared in a pH 9 buffer and used to analyze samples buffered to different pHs in the range of 6-10. Results can be compared with those obtained using a standard addition. 

Why is the acid-base indicator methyl red added to the solution ... 

The plT at which an acid-base indicator changes color is determined by its acid dissociation constant. For an indicator that is a monoprotic weak acid, ITIn, the following dissociation reaction occurs... 

A list of several common acid-base indicators, along with their piQs, color changes, and pH ranges, is provided in the top portion of Table 9.4. In some cases. 

Ladder diagram showing the range of pH levels over which a typical acid-base indicator changes color. 

The acidity constant for an acid-base indicator was determined by preparing three solutions, each of which has a total indicator concentration of 5.00 X 10- M. The first solution was made strongly acidic with HCl and has an absorbance of 0.250. The second solution was made strongly basic and has an absorbance of 1.40. The pH of the third solution was measured at 2.91, with an absorbance of 0.662. What is the value of K, for the indicator ... 

Ramsing and colleagues developed an FfA method for acid-base titrations using a carrier stream mixture of 2.0 X f0 M NaOH and the acid-base indicator bromthymol blue. Standard solutions of HCl were injected, and the following values of Af were measured from the resulting fiagrams. 

The indicator method is especially convenient when the pH of a weU-buffered colorless solution must be measured at room temperature with an accuracy no greater than 0.5 pH unit. Under optimum conditions an accuracy of 0.2 pH unit is obtainable. A Hst of representative acid—base indicators is given in Table 2 with the corresponding transformation ranges. A more complete listing, including the theory of the indicator color change and of the salt effect, is also available (1). 

It turns out that in low-viscosity blending the acdual result does depend upon the measuring technique used to measure blend time. Two common techniques, wliich do not exhaust the possibilities in reported studies, are to use an acid-base indicator and inject an acid or base into the system that will result in a color change. One can also put a dye into the tank and measure the time for color to arrive at uniformity. Another system is to put in a conductivity probe and injecl a salt or other electrolyte into the system. With any given impeller type at constant power, the circulation time will increase with the D/T ratio of the impeller. Figure 18-18 shows that both circulation time and blend time decrease as D/T increases. The same is true for impeller speed. As impeller speed is increased with any impeller, blend time and circulation time are decreased (Fig. 18-19). 

These steric factors are also indicated by the relative basicity of enamines derived from five-, six-, and seven-membered ketones. The five- and seven-membered enamines are considerably stronger bases, indicating better conjugation between the amine lone pair and the double bond. The reduced basicity of the cyclohexanone enamines is related to the preference for exo and endo double bonds in six-membered rings (see Section 3.10). 

Acid-base indicator Acid (or base). Neutralization is complete as determined by color change of indicator. 

Usually special cases of the full scheme are studied so that only one or two relaxation times are observed. Important examples are a solution of an acid-base solute in the presence of an acid-base indicator, and a buffered solution of an acid—base solute. PP... 

Scheme VIII has the form of Scheme II, so the relaxation time is given by Eq. (4-15)—appjirently. However, there is a difference between these two schemes in that L in Scheme VIII is also a participant in an acid-base equilibrium. The proton transfer is much more rapid than is the complex formation, so the acid-base system is considered to be at equilibrium throughout the complex formation. The experiment can be carried out by setting the total ligand concentration comparable to the total metal ion concentration, so that the solution is not buffered. As the base form L of the ligand undergoes coordination, the acid-base equilibrium shifts, thus changing the pH. This pH shift is detected by incorporating an acid-base indicator in the solution.

Protons bound to heteroatoms in heterocyclic compounds are likely to be very mobile in solution and, where two or more heteroatoms are present in a structure, different isomers (tautomers) may be in equilibrium. As a case in point, consider the nucleotide bases (indicates the point of attachment to the sugar-phosphate backbone). 

A detailed study of the transformations of methylpyrazolylketones into acetylenes under the action of PCI5 and then a base indicates the sensitivity of these reactions to experimental conditions, the structure of the starting ketones, and the nature of the base (69TZV927 69KGS1055 76TZV2288). 

You are probably familiar with a variety of aqueous solutions that are either acidic or basic (Figure 4.6). Acidic solutions have a sour taste and affect the color of certain organic dyes known as acid-base indicators. For example, litmus turns from blue to red in acidic solution. Basic solutions have a slippery feeling and change the colors of indicators (e.g., red to blue for litmus). 

The objective of the titration is to determine the point at which reaction is complete, called the equivalence point. This is reached when the number of moles of OH- added is exactly equal to the number of moles of acetic acid, HC O originally present To determine this point, a single drop of an acid-base indicator such as phenolphthalein is used. It should change color (colorless to pink) at the equivalence point. 

The flask contains vinegar (a dilute solution of acetic acid) and an add-base indicator (phenolphthalein) that is colorless in add solution and pink in basic solution. 

A less accurate but more colorful way to measure pH uses a universal indicator, which is a mixture of acid-base indicators that shows changes in color at different pH values (Figure 13.5, p. 359). A similar principle is used with pH paper. Strips of this paper are coated with a mixture of pH-sensitive dyes these strips are widely used to test the pH of biological fluids,... 

We will also consider the equilibrium involved when an acid-base indicator is used to estimate pH (Section 14.2). ... 

---