Band structure, atomic

Is 2s 2p 3s 3p 3d 4s. If the 3d states were truly core states, then one might expect copper to resemble potassium as its atomic configuration is ls 2s 2p 3s 3p 4s The strong differences between copper and potassium in temis of their chemical properties suggest that the 3d states interact strongly with the valence electrons. This is reflected in the energy band structure of copper (figure Al.3.27). 

At a surface, not only can the atomic structure differ from the bulk, but electronic energy levels are present that do not exist in the bulk band structure. These are referred to as surface states . If the states are occupied, they can easily be measured with photoelectron spectroscopy (described in section A 1.7.5.1 and section Bl.25.2). If the states are unoccupied, a teclmique such as inverse photoemission or x-ray absorption is required [22, 23]. Also, note that STM has been used to measure surface states by monitoring the tunnelling current as a fiinction of the bias voltage [24] (see section BT20). This is sometimes called scamiing tuimelling spectroscopy (STS). 

The pseudopotential is derived from an all-electron SIC-LDA atomic potential. The relaxation correction takes into account the relaxation of the electronic system upon the excitation of an electron [44]- The authors speculate that ... the ability of the SIRC potential to produce considerably better band structures than DFT-LDA may reflect an extra nonlocality in the SIRC pseudopotential, related to the nonlocality or orbital dependence in the SIC all-electron potential. In addition, it may mimic some of the energy and the non-local space dependence of the self-energy operator occurring in the GW approximation of the electronic many body problem [45]. 

The band-structure code, called BAND, also uses STO basis sets with STO fit functions or numerical atomic orbitals. Periodicity can be included in one, two, or three dimensions. No geometry optimization is available for band-structure calculations. The wave function can be decomposed into Mulliken, DOS, PDOS, and COOP plots. Form factors and charge analysis may also be generated. 

APW (augmented plane wave) a band structure computation method atomic mass unit (amu) atomic unit of mass... 

The band structure of four concentric armchair tubules with 10, 20, 30, and 40 carbon atoms around their circumferences (external diameter 27.12 A) was calculated, where the tubules were positioned to minimize the energj for all bilayered pairs 17). In this case, the four-layered tubule remains metallic, similar to the behavior of two double-layered armchair nanotubes, except that tiny band splittings form. 

Valence band spectra provide information about the electronic and chemical structure of the system, since many of the valence electrons participate directly in chemical bonding. One way to evaluate experimental UPS spectra is by using a fingerprint method, i.e., a comparison with known standards. Another important approach is to utilize comparison with the results of appropriate model quantum-chemical calculations 4. The combination with quantum-chcmica) calculations allow for an assignment of the different features in the electronic structure in terms of atomic or molecular orbitals or in terms of band structure. The experimental valence band spectra in some of the examples included in this chapter arc inteqneted with the help of quantum-chemical calculations. A brief outline and some basic considerations on theoretical approaches are outlined in the next section. 

Copper clusters containing two to four atoms have been formed (94) in argon and methane, whereas large, colloidal-copper particles resulted in dodecane matrices (94). The authors suggested that the "birth of the band structure of copper is clearly visible on passing from the dimer to the tetramer, with CU4 already possessing many of the features of the bulk metal (94). 

Single slab. A number of recent calculations of surface electronic structures have shown that the essential electronic and structural features of the bulk material are recovered only a few atomic layers beneath a metal surface. Thus, it is possible to model a surface by a single slab consisting of 5-15 atomic layers with two-dimensional translational symmetry parallel to the surface and vacuum above and below the slab. Using the two-dimensional periodicity of the slab (or thin film), a band-structure approach with two-dimensional periodic boundary conditions can be applied to the surface electronic structure. 

To describe the band structure of metals, we use the approach employed above to describe the bonding in molecules. First, we consider a chain of two atoms. The result is the same as that obtained for a homonuclear diatomic molecule we find two energy levels, the lower one bonding and the upper one antibonding. Upon adding additional atoms, we obtain an additional energy level per added electron, until a continuous band arises (Fig. 6.9). To describe the electron band of a metal in a... 

The valence band structure of very small metal crystallites is expected to differ from that of an infinite crystal for a number of reasons (a) with a ratio of surface to bulk atoms approaching unity (ca. 2 nm diameter), the potential seen by the nearly free valence electrons will be very different from the periodic potential of an infinite crystal (b) surface states, if they exist, would be expected to dominate the electronic density of states (DOS) (c) the electronic DOS of very small metal crystallites on a support surface will be affected by the metal-support interactions. It is essential to determine at what crystallite size (or number of atoms per crystallite) the electronic density of sates begins to depart from that of the infinite crystal, as the material state of the catalyst particle can affect changes in the surface thermodynamics which may control the catalysis and electro-catalysis of heterogeneous reactions as well as the physical properties of the catalyst particle [26]. 

---