Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Molds autoclave

Molds for autoclaving must be more substantial and can carry more detail. Depending on molding requirements and conditions, they can be produced by electroforming nickel. To cure large parts size restrictions and availability of autoclaves and ovens can occur. Additional heat is obtained by incorporating electrical heating elements in the molds. [Pg.429]

The oldest technology involved in the elastomer blending and vulcanization process is essentially a temperature controlled two roll mill as well as internal mixers followed by an optimum degree of crosslinking in autoclave molds (compression, injection, etc.) in a batch process or in a continuous process such as continuously heated tube or radiated tubes. A few examples of laboratory scale preparation of special purpose elastomeric blends is cited here. [Pg.465]

Techniques commonly used to manufacture advanced composites from prepregs, which are available in unidirectional fiber or fabric form, include compression molding, vacuum-bag autoclave molding, stamp molding, thermoforming, and on-line (in situ) consolidation [3]. In compression and vacuum-bag autoclave molding techniques, the prepreg is cut to the dimensions of the structure, and the fiber directions are oriented to obtain the required... [Pg.209]

Molding processes include compression molding, resin transfer molding (RTM), injection molding and reaction injection molding (RIM), autoclave molding, and several types of specific processes such as shell molding, which is used in foundries. [Pg.261]

Autoclave molding has been particularly adapted for the cure of laminates of preimpregnated plies of continuous fibers (prepregs). A lay-up of... [Pg.261]

Chottiner, J., Sanjana, Z, N., Kodani, M. R., Lengel, K. W., Rosenblatt, G. B. Monitoring cure of large autoclave molded parts by dielectric analysis, p. 77, Proc. 26th SAMPE Symp., 1981... [Pg.46]

Autoclave Molding. This is similar to pressure-bag molding, but it is carried out in an autoclave to apply the pressure to the outside of the cover film. [Pg.686]

Compression Molding Flexible Plunger Flexible Bag Molding Laminate Hand Lay-Up Vacuum Bag Molding Vacuum Bag Molding and Pressure Pressure Bag Molding Autoclave Molding Autoclave Press Clave Wet Lay-Up... [Pg.457]

See other pages where Molds autoclave is mentioned: [Pg.79]    [Pg.307]    [Pg.95]    [Pg.8]    [Pg.9]    [Pg.9]    [Pg.512]    [Pg.512]    [Pg.672]    [Pg.79]    [Pg.795]    [Pg.95]    [Pg.95]    [Pg.210]    [Pg.213]    [Pg.186]    [Pg.371]    [Pg.10]    [Pg.260]    [Pg.260]    [Pg.274]    [Pg.274]    [Pg.708]    [Pg.133]    [Pg.481]    [Pg.2316]    [Pg.3032]    [Pg.409]    [Pg.101]    [Pg.101]    [Pg.264]    [Pg.305]    [Pg.371]    [Pg.422]    [Pg.464]    [Pg.468]    [Pg.469]   
See also in sourсe #XX -- [ Pg.429 ]

See also in sourсe #XX -- [ Pg.429 ]



SEARCH



Autoclavation

Autoclave Autoclaving

Autoclave Molding of Graphite Epoxy Composites

Autoclave molding

Autoclave molding operation

Autoclaves

Autoclaving

Curing autoclave moldings

Processing autoclave molding

Reinforced-plastic autoclave molding

© 2024 chempedia.info