Combination tables amides

Following the trend towards lower carbonyl IR stretch frequencies, branching alpha to the amide carbonyl (Table 5, entries 53, 54, 62, 63 and 65) affects the shifts for mutagens and hydroxamic esters similarly and causes a marked downfield shift of up to 6 ppm relative to the acetamide substrate (Table 5, entry 60). These effects, as well as the smaller than expected downfield shift with ferf-butyl and neopentyl side chains are, as with the Ai-chlorohydroxamic esters, due to the combined influence of a stabilizing alkyl inductive effect together with destabilizing desolvation of the polar form of the amide carbonyl ". 

Some years ago we developed novel families of polydentate hgands of Schiff base and oxime type (L1-L4). Combining at least one imine with oxygen or nitrogen coordination sites (Scheme 1), they facilitate coupling of numerous azole and cyclic amide derivatives (Table 1, entry 1) with aryl bromides under nuld temperature conditions [36-39], [41-43]. With aryl iodides, some reactions were even performed at 25°C and a turnover of about 1,500 was achieved with pyrazole at higher temperature (80°C). This catalytic system is one of the rare examples amongst modem copper chemistry that has already been industrially applied. 

In order to produce high yields of ester in this manner it is necessary to remove the by-product ammonia (or amine) either by heating or combining with mineral acid, eg, H2SO4 or HCI. Recent work has shown that acidic ion-exchange resins can be used in place of mineral acids for converting sensitive unsubstituted amides (76). The stmctural relationships involved in esterification of amides are shown in Table 2 (77). 

Since mild activation conditions appear to be important, a number of solution activation conditions were tested. PAMAM dendrimers are comprised of amide bonds, so the favorable conditions for refro-Michael addition reactions, (low pH, high temperature and the presence of water) may be able to cleave these bonds. Table 1 shows a series of reaction tests using various acid/solvent combinations to activate the dendrimer amide bonds. Characterization of the solution-activated catalysts with Atomic Absorption spectroscopy, FTIR spectroscopy and FTIR spectroscopy of adsorbed CO indicated that the solution activation generally resulted in Pt loss. Appropriate choice of solvent and acid, particularly EtOH/HOAc, minimized the leaching. FTIR spectra of these samples indicate that a substantial portion of the dendrimer amide bonds was removed by solution activation (note the small y-axis value in Figure 4 relative... 

Carbon dioxide is a symmetrical, linear triatomic molecule (0 = C=0) with a zero dipole moment. The carbon-to-hydrogen bond distances are about 1.16A, which is about 0.06A shorter than typical carbonyl double bonds. This shorter bond length was interpreted by Pauling to indicate that greater resonance stabilization occurs with CO2 than with aldehydes, ketones, or amides. When combined with water, carbonic acid (H2CO3) forms, and depending on the pH of the solution, carbonic acid loses one or two protons to form bicarbonate and carbonate, respectively. The various thermodynamic parameters of these reactions are shown in Table I. 

The formation of isocyanurates in the presence of polyols occurs via intermediate allophanate formation, i.e, die urethane group acts as a cocatalyst in the dimerization reaction. By combining cyclotrimeiization with polyurethane formation, processibility is improved, and the friability of the derived foams is reduced. Modification of cellular polymers by incorporating amide, imide, oxazolidinone, or carbodiimide groups has been attempted but only the urethane-modified isocyanurate foams are produced in the 1990s. PUIR foams often do not require added fire retardants to meet most regulatory requirements. A typical PUIR foam formulation is shown in Table 2. 

By using glycine diphenylmethyl (Dpm) amide-derived Schiff base 22 as a key substrate and N-spiro chiral quaternary ammonium bromide lg as an ideal catalyst, a high enantioselectivity was achieved, even in the alkylation with less-reactive simple secondary alkyl halides, as shown in Table 5.5 [21]. This system offers a facile access to structurally diverse optically active vicinal diamines in combination with the subsequent reduction (Scheme 5.14) [21]. 

Table 13.4 also shows that the deprotonation of isopropanol with LiHMDS is less than half as exothermic as the deprotonations with LDA or LTMP. Hence, LiHMDS is a much weaker base than the other two amides. This is due to the ability of the SiMe3 groups of LiHMDS to stabilize the negative charge in the a-position at the N atom. The mechanism of this stabilization might be the same as in the case of the isoelectronic triphenylphosphonium center in P ylides (Figure 11.1), that is, a combination of an inductive effect and anomeric effect. Because of its relatively low basicity, LiHMDS is employed for the preparation of enolates primarily when it is important to achieve high chemoselectivity. 

---