Stress corrosion cracking aluminium

Resistance to stress-corrosion cracking Commercially pure titanium is very resistant to stress-corrosion cracking in those aqueous environments that usually constitute a hazard for this form of failure, and with one or two exceptions, detailed below, the hazard only becomes significant when titanium is alloyed, for example, with aluminium. This latter aspect is discussed in Section 8.5 under titanium alloys. 

The stress-corrosion cracking hazard for titanium alloys containing aluminium is significantly higher than that obtaining for commercially pure titanium, and in addition to stress-corrosion cracking in methanol and red... 

Sandoz, G., In Stress Corrosion Cracking in High Strength Steels and in Titanium and Aluminium Alloys, Ed. B.F. Brown, Naval Research Laboratory, Washington, pp. 79-145, (1972)... 

Stress-corrosion Cracking of Titanium, Magnesium and Aluminium Alloys... 

Stress-corrosion cracking occurs in certain aluminium alloys which have been developed for medium and high strength by employing variations in composition, cold work and heat treatment The main alloys are based upon Al-Mg, Al-Mg and Al-Cu, but stress corrosion also occurs in Al-Ag, Al-Cu-Mg, Al-Mg-Si, Al-Zn and Al-Cu-Mg-Zn alloys. It has... 

Later work on aluminium alloys has also focused more closely upon the role of hydrogen which had not previously been widely considered as an embrittling species in the stress-corrosion cracking process for these alloys. The idea was not new, however. Reports of intergranular failure under cathodic charging conditions had been made at a much earlier time . A reduction in stress-corrosion life and alloy ductility in a high purity Al-5Zn-3Mg alloy had been found in specimens pre-exposed to a 2% NaCI solution" , an effect that was accentuated if specimens were stressed". ... 

In more recent work embrittlement in water vapour-saturated air and in various aqueous solutions has been systematically examined together with the influence of strain rate, alloy composition and loading mode, all in conjunction with various metallographic techniques. The general conclusion is that stress-corrosion crack propagation in aluminium alloys under open circuit conditions is mainly caused by hydrogen embrittlement, but that there is a component of the fracture process that is caused by dissolution. The relative importance of these two processes may well vary between alloys of different composition or even between specimens of an alloy that have been heat treated differently. 

The oxygen concentration of the solution, as in many instances of corrosion, can also be critical in stress-corrosion cracking tests. Instances are available in the literature that show very markedly different test results according to the oxygen concentration in systems as widely different as austenitic steels immersed in chloride-containing phosphate-treated boiler water and aluminium alloys immersed in 3% NaCl. 

Fig, 8.99 Relative resistance to stress-corrosion cracking of three aluminium alloys subjected to different environments. The stress levels employed corresponded to 75, 50 and 25% of the respective transverse yield strengths (after Liflca and Sprowls )... 

Low-carbon and chromium-nickel steels, certain copper, nickel and aluminium alloys (which are all widely used in marine and offshore engineering) are liable to exhibit stress-corrosion cracking whilst in service in specific environments, where combinations of perhaps relatively modest stress levels in material exposed to environments which are wet, damp or humid, and in the presence of certain gases or ions such as oxygen, chlorides, nitrates, hydroxides, chromates, nitrates, sulphides, sulphates, etc. 

Recommended practice for examination and evaluation of pitting corrosion Test method for determining susceptibility to stress corrosion cracking of high-strength aluminium alloy products Test method for pitting and crevice corrosion resistance of stainless steels and related alloys by the use of ferric chloride solution Recommended practice for preparation and use of direct tension stress corrosion test specimens... 

S. Fonlupt, B. Bayle, D. Delafosse, J.L. Heuze, Role of second phases in the stress corrosion cracking of a nickel-aluminium bronze in saline water, Corros. Sci. 47 (2005) 2792-2806. 

Transgranular stress corrosion cracks are known [7.49] from i) austenitic steels in acidic chloride solutions, ii) low-strength ferritic steels in acidic media, iii) ferritic steels in phosphate solutions, iv) carbon steel in water saturated with CO2 and CO, v) a-brass in ammonia solutions that do not cause surface films, vi) aluminium alloys in NaCl/K2Cr04 solutions and vii) magnesium alloys in diluted fluoride solutions. For further study of fracture surface appearance, see, e.g. Lees [7.49] and Scully [7.53]. 

---