Aliquoting

To determine the exact diazomethane content, allow an aliquot portion of the ethereal diazomethane solution to react with an accurately weighed amount (say, about 1 g.) of A. R. benzoic acid in 60 ml. of anhydrous ether. The solution should be completely decolourised, thus showing that the benzoic acid is present in excess. Dilute the solution with water and titrate the excess of benzoic acid with standard 0 IN alkali using phenolphthalein as indicator. 

In resolving complex metal-ion mixtures, more than one masking or demasking process may be utilized with various aliquots of the sample solution, or applied simultaneously or stepwise with a single aliquot. In favorable cases, even four or five metals can be determined in a mixture by the application of direct and indirect masking processes. Of course, not all components of the mixture need be determined by chelometric titrations. For example, redox titrimetry may be applied to the determination of one or more of the metals present. 

A standard solution of Mn + was prepared by dissolving 0.250 g of Mn in 10 ml of concentrated HNO3 (measured with a graduated cylinder). The resulting solution was quantitatively transferred to a 100-mL volumetric flask and diluted to volume with distilled water. A 10-mL aliquot of the solution was pipeted into a 500-mL volumetric flask and diluted to volume, (a) Express the concentration of Mn in parts per million, and estimate uncertainty by a propagation of uncertainty calculation, (b) Would the uncertainty in the solution s concentration be improved... 

To test a spectrophotometer for its accuracy, a solution of 60.06 ppm K2Cr207 in 5.0 mM H2SO4 is prepared and analyzed. This solution has a known absorbance of 0.640 at 350.0 nm in a 1.0-cm cell when using 5.0 mM H2SO4 as a reagent blank. Several aliquots of the solution are analyzed with the following results... 

A standardization in which aliquots of a standard solution are added to the sample. 

Illustration showing the method of standard additions in which separate aliquots of sample are diluted to the same final volume. One aliquot of sample is spiked with a known volume of a standard solution of analyte before diluting to the final volume. 

II. 5 (arbitrary units). A second 50-mL aliquot of the sample, which is spiked with 1.00-mL of a 10.0-ppm standard solution of the analyte, gives a signal of 23.1. What is the concentration of analyte in the original sample ... 

An alloy of chromel containing Ni, Fe, and Cr was analyzed by a complexation titration using EDTA as the titrant. A 0.7176-g sample of the alloy was dissolved in ITNOa and diluted to 250 mb in a volumetric flask. A 50.00-mb aliquot of the sample, treated with pyrophosphate to mask the Fe and Cr, required 26.14 mb of 0.05831 M EDTA to reach the murexide end point. A second 50.00-mb aliquot was treated with hexamethylenetetramine to mask the Cr. Titrating with 0.05831 M EDTA required 35.43 mb to reach the murexide end point. Einally, a third 50.00-mb aliquot was treated with 50.00 mb of 0.05831 M EDTA, and back titrated to the murexide end point with 6.21 mb of 0.06316 M Cu +. Report the weight percents of Ni, fe, and Cr in the alloy. 

Each of these titrations was conducted on a 50.00-mF aliquot of the original 250.0-mF sample. The mass of each analyte, therefore, must be corrected by multiplying by a factor of 5. Thus, the grams of Ni, Fe, and Cr in the original sample are... 

Dissolve the sample in about 100 mL of H2O, and then dilute to the mark. Using a pipet, transfer a 25-mL aliquot of this solution to a 125-mL Erlenmeyer flask, and add 25-mL of H2O and 2 drops of bromocresol green indicator. Titrate the sample with 0.1 M HCl to the indicator s end point. 

Several aspirin tablets are ground to a fine powder in a mortar and pestle. A 0.1013-g portion of the powder is placed in a 1-L volumetric flask and diluted to volume with distilled water. A portion of this solution is filtered to remove insoluble binders, and a 10.00-mL aliquot transferred to a 100-mL volumetric flask containing 2.00 ml of 4 M NaOH. After diluting to volume the fluorescence of the resulting solution is found to be 8.69. What is the %w/w acetylsalicylic acid in the aspirin tablets ... 

The concentration of Ca + in a sample of sea water is determined using a Ca ion-selective electrode and a one-point standard addition. A 10.00-mL sample is transferred to a 100-mL volumetric flask and diluted to volume. A 50.00-mL aliquot of sample is placed in a beaker with the Ca ion-selective electrode and a reference electrode, and the potential is measured as -0.05290 V. A 1.00-mL aliquot of a 5.00 X 10 M standard solution of Ca + is added, and a potential of -0.04417 V is measured. What is the concentration of Ca + in the sample of sea water ... 

The concentration of NO3 in a water sample is determined by a one-point standard addition using an N03 ion-selective electrode. A 25.00-mL sample is placed in a beaker, and a potential of -t0.102 V is measured. A 1.00-mL aliquot of a 200.0 ppm standard solution of N03 is added, after which the potential is found to be -t0.089 V. Report the concentration of N03 in parts per million. 

Determine the parts per million of F in the tap water, (b) For the analysis of toothpaste a 0.3619-g sample was transferred to a 100-mL volumetric flask along with 50.0 mL of TISAB and diluted to volume with distilled water. Three 20.0-mL aliquots were removed, and the potential was measured with an L ion-selective electrode using a saturated calomel electrode as a reference. Live separate 1.00-mL additions of a 100.0-ppm solution of L were added to each, measuring the potential following each addition. 

With conventional nonspectroscopic detectors, other methods must be used to identify the solutes. One approach is to spike the sample by adding an aliquot of a suspected analyte and looking for an increase in peak height. Retention times also can be compared with values measured for standards, provided that the operating conditions are identical. Because of the difficulty of exactly matching such conditions, tables of retention times are of limited utility. 

Samples and calibration standards are prepared for analysis using a 10-mL syringe. Add 10.00 mL of each sample and standard to separate 14-mL screw-cap vials containing 2.00 mL of pentane. Shake vigorously for 1 min to effect the separation. Wait 60 s for the phases to separate. Inject 3.0-pL aliquots of the pentane layer into a GC equipped with a 2-mm internal diameter, 2-m long glass column packed with a stationary phase of 10% squalane on a packing material of 80/100 mesh Chromosorb WAW. Operate the column at 67 °C and a flow rate of 25 mL/min. 

To verify the method a 1.00-mL aliquot of a standard solution of 40.0-ppm glucose was added to 1.00 ml of the combined reagents, requiring 34.6 s to produce the same extent of reaction. Determine the calculated concentration of glucose in the standard and the percent error for the analysis. 

In a typical analysis a 10.0-mg sample is dissolved in water and diluted to volume in a 25-mL volumetric flask. A 125- tL aliquot is transferred to a 25-mL volumetric flask and diluted to volume with a pH 9 buffer. When injected into the flow injection apparatus a signal of 21.4 is obtained. What is the %w/w cocaine in the sample ... 

The complication of matching the matrix of the standards to that of the sample can be avoided by conducting the standardization in the sample. This is known as the method of standard additions. The simplest version of a standard addition is shown in Figure 5.5. A volume, V, of sample is diluted to a final volume, Vf, and the signal, is measured. A second identical aliquot of sample is... 

Static headspace GC/MS. The partitioning of volatile and semivolatile compounds between two phases in a sealed container. An aliquot of the headspace gas generated is injected onto a gas chromatographic column. This is followed by mass spectrometric analysis of compounds eluting from the gas chromatograph. 

---