Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Aerosil

The purpose of these work are consist in comparative research of sorption properties unmodified aerosile A-300 and its modified analogue - K-7-30 for selective evolving of microquantities of Al (111), Ga (111), In (111) at consistent presence, as well as Mo (VI) and W (VI). [Pg.265]

Sorption activity differences of listed elements on aerosile A-300 and K-7-30 have been established depending from pH media. It was marked that disparity of pH sorption optimum values (pH, ) is caused by changes of composition and stmcture of hydrated cover ot sorbents. The presence of hydrated and a solvate surface layer on K-7-30 is the reason of differences at degree of hydrolysis of taken elements and composition of their hydrolyzed forms. [Pg.265]

The researches on fastening of some organic reagents on different carriers (polyurethane foam of marks T 25-3,8, chromatographic paper of marks FN 5 and aerosil) are carried out by us. [Pg.330]

The research of congo red and stilbazo adsoi ption on aerosil is carried out. The test - techniques of hydrargymm and cupmm determination with the use of obtained solid phase reagents are designed. [Pg.330]

Basic characteristics of Aerosil. Degussa Bulletin 11. Degussa, Hanau, 1997. [Pg.674]

As revealed by IR-spectroscopy, the attachment of the polymer proceeds via acylation of aminopropyls absorbances of both amides (1650 cm-1) and esters (1740 cm-1) contribute to the spectrum of polyacrylate-coated aminopropyl-Aerosil (specific surface area 175 m2/g) [55], During the reaction, the accumulation of p-nitrophenyl ester groups in the support is accompanied by the liberation of p-nitrophenol into the contacting solution. Thus, the evaluation of the conformational state of adsorbing macromolecules can be performed by the simultaneous study of both processes by UV-spectroscopy as shown in Fig. 7. Apparently, at... [Pg.155]

Fig. 7a, b. Kinetics of poly(p-nitrophenyl acrylate) chemical adsorption on aminopropyl-Aerosil at 25 °C in dimethylsulphoxide. Filled circles ester group content (pmol/g support), empty c/rc/ei p-nitrophenol release (pmol/g support), a — l%solution b — 5% solution [55]... [Pg.155]

The authors of [99] proposed a calorimetric method for determining the degree of the polymer-filler interaction the exothermal effect manifests itself in the high energy of the polymer-filler adhesion, the endothermal effect is indicative of a poor, if any, adhesion. The method was used to assess the strength of the PVC-Aerosil interaction with Aerosil surface subjected to different pre-treatments... [Pg.11]

Similar results were also reported in [100], As noted earlier, the authors measured the strength of the filler-matrix interaction by the magnitude of the thermal effect the more negative the enthalpy, the greater the interaction. Pure A-175 Aerosil and Aerosils modified with aminophenyl methylene diethoxysilane (AM-2) and butyl alcohol ( Butasil ). The base polymer was PVC plasticized with dioctyl sebacinate. The results are presented in Table 8 below. [Pg.35]

Table 15. Physico-mechanical characteristics and heats of mixing with chloroform (dH3) of poly(butyl methacrylate) polymerization-filled with aerosil (10% by mass) [333, 334]... Table 15. Physico-mechanical characteristics and heats of mixing with chloroform (dH3) of poly(butyl methacrylate) polymerization-filled with aerosil (10% by mass) [333, 334]...
The authors of [344] investigated PS based composites prepared by compounding unmodified Aerosil with Aerosil to which a PS layer was grafted. The MM of the matrix and the grafted layer was 3 x 105. The resultant composites are characterized in Table 16 below. [Pg.54]

Compo- sition No. Free PS, % Bound PS, % Filler (Aerosil) % Frequency cos-1 Shift factor b(c) used to reduce G (co)... [Pg.55]

However, when using supports with weak linkage between the primary particles of the catalyst, its splitting occurs quickly and it is unlikely to influence the shape of the kinetic curve. For example, in the case of chromium oxide catalyst reduced by CO supported on aerosil-type silica, steady-state polymerization with a very short period of increasing rate is possible (see curve 1, Fig. 1). [Pg.181]

Loader 38) studied the Raman spectra of styrene adsorbed on different silicas—chromatographic grade silica gel, Cab-O-Sil, and Aerosil 380. The author utilized the fact that chemisorption will bring about marked changes in the spectrum whereas physical adsorption will cause only a broadening of the Raman lines accompanied in some cases by a frequency... [Pg.338]

Influence of Metal Particle Size in Nickel-on-Aerosil Catalysts on Surface Site Distribution, Catalytic Activity, and Selectivity... [Pg.427]

For a model particle, titanium dioxide (Ti02, Nippon Aerosil, P-25) having its primary size of 21nm was used, which was normally impossible to be uniformly fluidized. [Pg.486]

The application of infrared photoacoustic spectroscopy to characterize silica and alumina samples is reported. High quality infrared photoacoustic spectra illuminate structural changes between different forms of silica and alumina, as well as permit adsorbate structure to be probed. Adsorption studies on aerosil suggest adsorbed species shield the electric fields due to particle-particle interactions and induce changes in the vibrational spectra of the adsorbates as well as in the bulk phonon band. It is shown that different forms of aluminum oxides and hydroxides could be distinguished by the infrared spectra. [Pg.449]

Figure 1c shows the spectrum of aerosil that has been slurried in water and then dried at 100 C. This treatment initiates gel formation, so that the sample is no longer a chain of silica particles held together by electrostatic forces, but a porous network held together by siloxane linkages. The most obvious features in this spectrum are an increase in the water adsorption features at 3400 cm"" and 1632 cm". In addition, a band at 976 cm" is evident, that was much less obvious in the spectra of the other two silica samples. This feature is due to siloxane bridges formed during gel formation (10,12). [Pg.452]

Infrared spectra of silicas, a) Aerosil dried at 350 C, b) Aerosil as received, c) Aerosil slurried in water and dried at 100 C, d) Silicalite as received. [Pg.453]

An aerosil sample was methoxylated at 400 C to examine the effect of surface composition on the infrared spectrum. The difference spectrum between the methoxylated silica and the dried silica is shown in Figure 2b. Comparing this with the difference spectrum for hydroxylated silica (2a) several changes are apparent. First, the band due to the hydroxyl stretches at 3744 cm is diminished and replaced by bands at 2958 and 2856 cm" due to the asymmetric and symmetric CH stretching modes of the adsorbed methoxy. [Pg.455]

The infrared photoacoustic spectra presented here complement and extend previous results from transmission infrared studies. As an extension of previous studies of silica the photoacoustic results presented here have identified features in the infrared spectra that coincide with bulk phonon modes between 1000 and 1200 cm and below 500 cm . The photoacoustic spectra of water adsorbed on aerosil... [Pg.459]

Granulated fly ash [6] can substitute for Portland cement to an extent of 40% to 60%. Fly ash is used in granulated form and has a moisture content around 10% to 20%. The formulation can be used for cementing oil and gas wells within a temperature range of 20° to 250° C. The solution has reduced water absorption and increased sedimentation stability. A formulation [1388] is shown in Table 18-2. Hydrosil (Aerosil) is used to increase the adhesion of the produced cement rock to the casing string. It also reduces the density and water absorption. [Pg.280]

Aerosil. Aerosil as a solid additive in combination with diesel is active as a defoamer [962]. The aerosil is modified with bifunctional silicoorganic compounds. The composition is added to drilling solution in the form of a 3% to 5% suspension, in an amount of 0.02% to 0.5% by weight of aerosil per weight of drilling solution. [Pg.322]


See other pages where Aerosil is mentioned: [Pg.585]    [Pg.76]    [Pg.76]    [Pg.91]    [Pg.251]    [Pg.252]    [Pg.258]    [Pg.19]    [Pg.493]    [Pg.416]    [Pg.23]    [Pg.24]    [Pg.52]    [Pg.52]    [Pg.53]    [Pg.53]    [Pg.337]    [Pg.337]    [Pg.337]    [Pg.339]    [Pg.191]    [Pg.452]    [Pg.452]    [Pg.454]    [Pg.153]    [Pg.187]    [Pg.100]    [Pg.66]   
See also in sourсe #XX -- [ Pg.3 ]

See also in sourсe #XX -- [ Pg.7 , Pg.12 ]

See also in sourсe #XX -- [ Pg.6 , Pg.7 , Pg.9 ]

See also in sourсe #XX -- [ Pg.9 ]

See also in sourсe #XX -- [ Pg.313 ]

See also in sourсe #XX -- [ Pg.68 , Pg.200 ]

See also in sourсe #XX -- [ Pg.185 , Pg.186 , Pg.200 , Pg.288 , Pg.290 , Pg.292 , Pg.293 , Pg.294 , Pg.295 , Pg.297 ]

See also in sourсe #XX -- [ Pg.165 ]

See also in sourсe #XX -- [ Pg.188 ]

See also in sourсe #XX -- [ Pg.262 ]

See also in sourсe #XX -- [ Pg.409 ]

See also in sourсe #XX -- [ Pg.251 ]

See also in sourсe #XX -- [ Pg.541 ]

See also in sourсe #XX -- [ Pg.291 ]

See also in sourсe #XX -- [ Pg.291 ]

See also in sourсe #XX -- [ Pg.121 , Pg.329 ]

See also in sourсe #XX -- [ Pg.126 ]

See also in sourсe #XX -- [ Pg.359 , Pg.360 , Pg.361 , Pg.364 , Pg.370 ]

See also in sourсe #XX -- [ Pg.344 ]

See also in sourсe #XX -- [ Pg.595 ]

See also in sourсe #XX -- [ Pg.541 ]

See also in sourсe #XX -- [ Pg.40 , Pg.50 ]

See also in sourсe #XX -- [ Pg.144 ]

See also in sourсe #XX -- [ Pg.54 , Pg.200 ]

See also in sourсe #XX -- [ Pg.288 , Pg.290 , Pg.292 , Pg.294 , Pg.295 , Pg.399 , Pg.400 , Pg.401 , Pg.499 ]

See also in sourсe #XX -- [ Pg.200 , Pg.317 ]

See also in sourсe #XX -- [ Pg.144 ]

See also in sourсe #XX -- [ Pg.158 , Pg.159 ]

See also in sourсe #XX -- [ Pg.91 ]




SEARCH



AEROSIL for PVC Plastisols

Aerosil Fumed Silica

Aerosil Rhodorsil

Aerosil difference spectra

Aerosil silica particles

Aerosils

Aerosils

Hydrophobic aerosil

Silica Aerosil

Support Aerosil

Trimethylsilyl aerosil

© 2024 chempedia.info