Absorption, peak

Application of the exact continuum analysis of dispersion forces requires significant calculations and the knowledge of the frequency spectmm of the material dielectric response over wavelengths X = 2irc/j/ around 10-10 nm. Because of these complications, it is common to assume that a primary absorption peak at one frequency in the ultraviolet, j/uv. dominates the dielectric spectrum of most materials. This leads to an expression for the dielectric response... 

Dimethyl-2-butene and 2,5-dimethylhexadiene have absorption peaks at 192 and 243 nm in the ultraviolet. Which peak corresponds to which compound What are the approximate HOMO-LUMO separations in electron volts ... 

A typical IR spectrum such as that of hexane m Eigure 13 31 appears as a series of absorption peaks of varying shape and intensity Almost all organic compounds exhibit a peak or group of peaks near 3000 cm due to carbon-hydrogen stretching The peaks at 1460 1380 and 725 cm are due to various bending vibrations... 

Section 13 21 Transitions between electronic energy levels involving electromagnetic radiation m the 200-800 nm range form the basis of UV VIS spec troscopy The absorption peaks tend to be broad but are often useful m indicating the presence of particular tt electron systems within a mole cule... 

A particular vibration will give an absorption peak in the IR spectrum only if the dipole moment of the molecule changes dunng the vibration Which vibration of carbon dioxide the sym metric stretch or the antisymmetric stretch is infrared active 2... 

In a MALDl experiment, the sample is mixed or dissolved in a matrix material that has an absorption spectrum matching the laser wavelength of energy, The sample may not have a matching absorption peak (a), but this is not important because the matrix material absorbs the radiation, some of which is passed on to the dissolved sample. Neutral molecules and ions from both sample and matrix material are desorbed (b). 

The amount of a particular component in a sample can be monitored by examining the height of a spectral absorption peak The reduction of an aldehyde to an alcohol would show up as a decrease in line intensity for the carbonyl and an increase for the hydroxyl peaks in the spectrum. Changes in the relative importance of different relaxation modes in a polymer can also be followed by the corresponding changes in a mechanical spectrum. 

Different light-absorbing groups, called chromophores, absorb characteristic wavelengths, opening the possibility of qualitative analysis based on the location of an absorption peak. 

Laser Raman Microprobe. A more sophisticated microscope is the Laser Raman Microprobe, sometimes referred to as MOLE (the molecular orbital laser examiner). This instmment is designed around a light microscope to yield a Raman spectmm (45) on selected areas or particles, often <1 ia volume. The data are related, at least distantly, to iafrared absorption, siace the difference between the frequency of the exciting laser and the observed Raman frequency is the frequency of one of the IR absorption peaks. Both, however, result from rotational and vibrational states. Unfortunately, strong IR absorption bands are weak Raman scatterers and vice versa hence there is no exact correspondence between the two. 

Table 2. Absorption Peaks of Gel-Silica Monolith Pore Water and Surface Hydroxyl Groups ...

Table 10.4 Main IR absorption peaks for selected gases ...

The movement of gases and vapors is more difficult to visualize than that of particulates. However, most gases and vapors have strong absorption peaks in the infrared band. If a flat screen, heated to some 15 C or more above ambient temperature, is positioned on one side of a source with an infrared camera and filter on the other side, then the gas cloud will absorb a certain amount of infrared. Although the basic method is simple, special equipment (camera and filters) is required. 

Explain why, in the study of an acid-base equilibrium, we observe absorption peaks of both species (conjugate acid and base) when using electronic absorption spectroscopy, but only a single peak by NMR. 

This absorber is basically a panel attached to a structural wall that is designed to absorb energy. The absorber is therefore frequency dependent and has an absorption peak at its resonant frequency. This type of absorber is not commonly used. 

To define the position of an absorption, the NMR chart is calibrated and a reference point is used. In practice, a small amount of tetramethylsilane [TMS (CH )4Si] Is added to the sample so that a reference absorption peak is produced when the spectrum is run. TMS is used as reference for both l H and 13C measurements because it produces in both a single peak that occurs upfield of other absorptions normally found in organic compounds. The ]H and 13C spectra of methyl acetate in Figure 13.3 have the l MS reference peak indicated. 

The compound whose 1H NMR spectrum is shown has the molecular formula C4H7O2CI and has an infrared absorption peak at 1740 cm-1. Propose a structure. 

---