Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Yield level

For high rotational levels, or for a moleeule like OFI, for whieh the spin-orbit splitting is small, even for low J, the pattern of rotational/fme-stnieture levels approaehes the Flund s ease (b) limit. In this situation, it is not meaningful to speak of the projeetion quantum number Rather, we first eonsider the rotational angular momentum N exelusive of the eleetron spin. This is then eoupled with the spin to yield levels with total angular momentum J = N + dand A - d. As before, there are two nearly degenerate pairs of levels assoeiated... [Pg.2076]

Fabric preparation is often considered to be the most important stage to obtain good color yields, levelness, and brightness on wool fabric (104). This is done almost exclusively by an oxidative chlorination process, the most popular commercial methods using either a batch treatment with dichloroisocyanuric acid (DCCA), or a continuous fabric treatment with gaseous chlorine, called the Kroy process. [Pg.348]

There has been much research aimed at developing N2 fixing systems for greater yield levels. For practical reasons, such systems cannot entirely substimte for mineral N fertilizers, and there is the difficult dilemma that N2 fixation within the ricefield is inhibited by additions of mineral N. [Pg.158]

The quantum yield of formation of substitution product increases with increasing concentration of the nucleophile at relatively low concentrations. At higher concentrations the value of the quantum yield levels off to reach a constant value (Figure 2). [Pg.228]

In the Riser Simulator it was possible for the MAB catalyst to reach slurry oil yield levels compatible with the conventional LZM catalyst operating at typical conditions for maximum mid-distillate. However, the yields of heavy naphtha range aromatics were half of those obtained with the LZM catalyst compared at the same slurry oil yield (Figure 2.12). The MAB ClO-Cll aromatics trend as a function of slurry oil yield was a continuation of the inert catalyst trend, an indication that a similar reaction mechanism could be taking place. The minimum slurry oil yield for the inert catalyst, even at maximum severity, was still above 40 wt% ... [Pg.32]

Yield levels of maize, sorghum, millet and rice at that time were about 600 kg ha" ... [Pg.353]

Some control can be built in by specifying minimum contents of actives, but this standard is prone to downward revision for reasons of commercial expediency in times when the harvest yields levels of actives that are mainly below the specification. At such times, it is likely that parcels of the herb meeting a particular specification will carry a price premium. [Pg.306]

The higher yield of HCN for PA6 + FR for well-ventilated flaming corresponds to a higher yield of CO for the same conditions. It is interesting to note that the HCN yield increases with the severity of the lire condition, whereas the CO yield levels off or even decreases. Results are consistent with the TGA/FTIR data presented in Table 19.3, Section 19.3.3.3. [Pg.525]

Yield level Generally higher crop yields were realized Medium yields health and nutrition problems Decreasing yields Decreasing yields... [Pg.13]

The time-dependent evolution of the level populations may also be dependent upon power. As described in Sect. 4, the GSA/ESA mechanism yields level populations that decay with their natural decay rate in the absence of excitation power. The Ni and N2 decay curves in the pure GSA/ESA Emit are therefore independent of excitation power. This is not true for the GSA/ETU mechanism, which continues to function after termination of the excitation source. All of the time-dependence curves discussed in Sect. 4 were calculated using Eq. (10) under low-power conditions. In this limit, when k2>kij the kinetics inherent to level 1 are rate determining and the decay behaviors for the two metastable populations determined from integration of Eq. (13) are given by... [Pg.21]

CNC FACEGARD A is a solubilizing agent for acrylic fibres, but under the proper concentrations and conditions, it acts as a swelling agent making the fibre more receptive to disperse and cationic colors and giving better yield, levelness and fixation. [Pg.177]

Allyl alcohol decreases the quantum yields of product formation. The quantum yields level off at higher allyl alcohol concentrations. The limiting value is approximately the same at 27.6 and 73.0 °C. It may well be assumed that the limiting quantum yields are related to an intramolecular non-radical decomposition. However, according to Chen and Volman, the residual reaction is essentially a geminate one occurring between methyl and formyl radicals that have been formed from the same aldehyde molecule in a solvent cage, viz. [Pg.296]


See other pages where Yield level is mentioned: [Pg.11]    [Pg.28]    [Pg.204]    [Pg.334]    [Pg.918]    [Pg.918]    [Pg.9]    [Pg.452]    [Pg.206]    [Pg.14]    [Pg.54]    [Pg.72]    [Pg.93]    [Pg.618]    [Pg.148]    [Pg.236]    [Pg.273]    [Pg.321]    [Pg.351]    [Pg.353]    [Pg.206]    [Pg.11]    [Pg.28]    [Pg.174]    [Pg.19]    [Pg.549]    [Pg.91]    [Pg.104]    [Pg.133]    [Pg.397]    [Pg.308]    [Pg.676]    [Pg.125]    [Pg.1292]    [Pg.1294]    [Pg.204]    [Pg.40]    [Pg.67]   
See also in sourсe #XX -- [ Pg.98 ]




SEARCH



© 2024 chempedia.info