Yield aluminium

Zinc decomposes mercury diproj yl at 100° to 120° C. with the formation of zinc dipropyi aluminium at 130° C. yields aluminium tripropyl, and beryllium gives beryllium dipropyl. 

Condensation products formed by acetone and chloroform do not appear to ha "e been very thoroughly investigated, but iodine decomposes aluminium triphenyl, yielding aluminium iodide and iodobenzene. 

When studying the same reaction with a variety of allylic bromides it was found that the addition of metallic aluminium dramatically improved the yield (aluminium chloride, aluminium oxide and metalUc zinc were ineffective). 

Figure B3.2.10. Contour plot of the electron density obtained by an orbital-free Hohenberg-Kolnr teclmique [98], The figure shows a vacancy in bulk aluminium in a 256-site cell containing 255 A1 atoms and one empty site, the vacancy. Dark areas represent low electron density and light areas represent high electron density. A Kolm-Sham calculation for a cell of this size would be prohibitively expensive. Calculations on smaller cell sizes using both techniques yielded densities that were practically identical.

The salt-like carbides. Among these are aluminium tricarbide imethanide) AI4C3 (containing essentially C ions) in the crystal lattice and the rather more common dicarbides containing the C ion, for example calcium dicarbide CaCjt these carbides are hydrolysed by water yielding methane and ethyne respectively ... 

Evidence for the solvated electron e (aq) can be obtained reaction of sodium vapour with ice in the complete absence of air at 273 K gives a blue colour (cf. the reaction of sodium with liquid ammonia, p. 126). Magnesium, zinc and iron react with steam at elevated temperatures to yield hydrogen, and a few metals, in the presence of air, form a surface layer of oxide or hydroxide, for example iron, lead and aluminium. These reactions are more fully considered under the respective metals. Water is not easily oxidised but fluorine and chlorine are both capable of liberating oxygen ... 

Friedel and Crafts reaction. alkyl halide condenses with an aromatic hydrocarbon in the presence of anhydrous aluminium chloride to yield, in the first instance, a hydrocarbon in accordance with the following scheme —... 

The yield of iso-propylbenzene is influenced considerably by the quality of the anhydrous aluminium chloride employed. It Is recommended that a good grade of technical material be purchase in small bottles containing not more than 100 g. each undue exposure to the atmosphere, which results in some hydrolysis, is thus avoided. Sealed bottles containing the reagent sometimes have a high internal pressure they should be wrapped in a dry cloth and opened with care. 

The apparatus required is similar to that described for Diphenylmelhane (Section IV,4). Place a mixture of 200 g. (230 ml.) of dry benzene and 40 g. (26 ml.) of dry chloroform (1) in the flask, and add 35 g. of anhydrous aluminium chloride in portions of about 6 g. at intervals of 5 minutes with constant shaking. The reaction sets in upon the addition of the aluminium chloride and the liquid boils with the evolution of hydrogen chloride. Complete the reaction by refluxing for 30 minutes on a water bath. When cold, pour the contents of the flask very cautiously on to 250 g. of crushed ice and 10 ml. of concentrated hydrochloric acid. Separate the upper benzene layer, dry it with anhydrous calcium chloride or magnesium sulphate, and remove the benzene in a 100 ml. Claisen flask (see Fig. II, 13, 4) at atmospheric pressure. Distil the remaining oil under reduced pressure use the apparatus shown in Fig. 11,19, 1, and collect the fraction b.p. 190-215°/10 mm. separately. This is crude triphenylmethane and solidifies on cooling. Recrystallise it from about four times its weight of ethyl alcohol (2) the triphenylmethane separates in needles and melts at 92°. The yield is 30 g. 

Aroylbenzoic acids. Aromatic hydrocarbons condense with phthalic anhydride in the presence of anhydrous aluminium chloride producing aroylbenzoic acids in good yields ... 

Dihydroxyacetophenone (II) can be prepared in good yield by heating hydroquinone diacetate (I) in the presence of 3-3 mols of aluminium chloride, Hydroquinone cannot be acylated by the Eriedel-Crafts method. 

An improved yield is obtained by the following process. Add a mixture of 75 g. (70-5 ml.) of propionyl chloride and 90 g. (103 ml.) of sodium-dried A.R. benzene to a vigorously stirred suspension of 75 g. of finely-powdered anhydrous aluminium chloride in 100 ml, of dry carbon disulphide, Then introduce more of the aluminium chloride (about 15 g.) until no further evolution of hydrogen chloride occurs. The yield of propiophenone, b.p. 123°/25 mm., is about 90 g. 

Method 2. Into a 500 ml. round-bottomed flask place 120 ml. of dry A.R. benzene, and 35 g. (29 ml.) of redistilled benzoyl chloride. Weigh out 30 g. of finely-powdered, anhydrous aluminium chloride into a dry corked test-tube, and add the solid, with frequent shaking, during 10 minutes to the contents of the flask. Fit a reflux condenser to the flask, and heat on a water bath for 3 hours or until hydrogen chloride is no longer evolved. Pour the contents of the flask wliile still warm into a mixture of 200 g. of crushed ice and 100 ml. of concentrated hydrochloric acid. Separate the upper benzene layer (filter first, if necessary), wash it with 50 ml. of 5 per cent, sodium hydroxide solution, then with water, and dry with anhydrous magnesium sulphate. Isolate the benzophenone as in Method 1. The yield is 30 g. 

---