Waiting

Once the cementation has been completed the rig will wait on cement (V OC), i.e. wait until the cement hardens prior to running in with a new assembly to drill out the plugs, float collar and shoe, all of which are made of easily drillable materials. 

Capital allowances may be accepted as soon as the capital Is spent or may have to wait until the asset is actually brought into use. In the case of the newcomer company or the ring-fenced project the allowance may only be able to commence once there is revenue from the project. 

Recently, EFIT has been extended to simulate elastic waves in homogeneous anisotropic media [3, 4] and inhomogeneous anisotropic media [5, 6]. Since Waite et al. [7,... 

Klaholz, S. Langenberg, K.. ]. Baum, P. Waite, F. Review of Progress in Quantitative Nondestructive Evaluation, 14 219-226, Plenum Press, New York, 1995... 

Products of the described type have very high quality requirements as the consumers are typically families with children or restaurants catering to same, where even the smallest bones are unacceptable. Previously, sample tests were conducted on selected blocks. The blocks were thawed and sieved. This was a very slow way of inspection where the production line had to wait for the raw material. 

The coimection between the Porter-Thomas P(lc) distribution and RRKM theory is made tln-ough the parameters j -and v. Waite and Miller [99] have studied the relationship between the average of the statistical... 

Waite B A and Miller W H 1980 Model studies of mode specificity in unimolecular reaction dynamics J. Chem. Phys. 73 3713-21... 

NOEs between nuclei are often exploited to demonstrate their spatial proximity, as described in the final section. It is possible to obtain decoupled NMR spectra without the complications of the NOE, by confining the decoupling irradiation to the period of the FID alone, and then waiting for 10 x before... 

The characteristic time of the tliree-pulse echo decay as a fimction of the waiting time T is much longer than the phase memory time T- (which governs the decay of a two-pulse echo as a function of x), since tlie phase infomiation is stored along the z-axis where it can only decay via spin-lattice relaxation processes or via spin diffusion. 

Wait a few minutes after the pellet has completely dissolved, and then continue taking readings as before until three consistent values are obtained. A second weighed pellet may then be added if desired, and the process repeated. 

This operation of weighing out the sample of substance to be analysed may conveniently be carried out while waiting for the absorption tubes to mature after polishing. 

Mitchell, A.R. and Wait, R., 1977. The Finite Element Method in Partial Differential Ecjualions, Wiley, London. 

A class of 20 students has access to only one copy of GAUSSIAN. Need they wait in line to write their input files on this one machine ... 

The reduction of catalysts warranted the additional stir time. 96 hours maybe excessive, I believe they were hoping it would turn green and the longerthey waited the more they thought it was a lost cause. Fortunately it worked out on the +++ side )"... 

To separate the oil added an equal volume of fresh cool water (note waited until solution cooled before adding the water). The oil started to drop out perfectly, used DCM to extract all traces of the oil. This woik up is by far the cleanest, easiest and simplest to date... (This dreamer was tried all method of ketone synthesis)... Once the oil was extracted, the extracts were pooled washed with sodium bicarbonate lx, saturated solution of NaCI 1x, and two washes with fresh dHzO... Some time was required for the work up as there was a little emulsion from the use of the base wash and then with the first water wash. The JOC ref suggested using an alumina column to remove the catalyst (could be a better way to go). 

We start rxn, one drop / second or so C in B. Sometimes we close sep funnel and shake flask B to ensure a constant rate of MeONO generation. Addition speed is limited by equilibrium of pressure between flasks. If it is too much quick, then MeONO gas go through sep. funnel, then we close the sep funnel and wait a bit till generation is low. The addition of C in B takes 1 hour, we close sep funnel and shake a bit B to finish reaction. If rxn (A) climbs temp too much, we can add ice in the water bath. I ve monitorized temp touching a part of solution that was out of water bath. At the final part may be water is to much cool, so we can take it out. After the addition of C in B we wait one more hour. 

And in the recipe above, Vogel want s to get rid of a secondary alcohol just like the one on MD-P2Pol and replace it with a bromine. Wait a minuter you may say, That isn t a double bond like... 

With bromo or iodo compound in hand it is time to quit and turn one s self over to the proper authorities. Wait There are a few who wouid continue. Most likeiy in the following manner. 

Start the heat and wait. It will take about 20 minutes to get going and there usually isn t much to see. The flask will be a nice orange colour from the bromine and it won t change much until just before the end. Make sure the water Is running, everything is secure and leave for three hours - have a sleep or something to eat maybe. 

The first few millilitres of distillate is likely to be unreacted benzo-dioxole. This will come over at about 8CTC. The best thing to do here is wait for the temperature to get to about 9CfC and then stop everything, change flasks and start again. Don t allow the reaction flask to heat up while you change flasks, in fact let it cool down a bit - if you don t, you ll know why I said this. 

Note 3. This means that the metal has been activated sufficiently. If the reaction does not start directly, one should wait (and observe the thermometer) for at least 30 min. After this period one can add a second portion of about 5 ml of R-Br if nothing has yet happened. 

A suspension of 0.35 mol of sodium amide in 400 ml of liquid ammonia was prepared in the usual way (e./. Chapter II, Exp. 11) (note 1). To this suspension was added with swirling 0.30 mol of 1-methylthio-l-propyne, in portions of about 10 g, waiting about 10 s after the addition of each portion. Swirling was continued for 1.5 min after the addition of the last portion. Immediately thereafter the... 

---