Temperature, viii

Studies to determine the nature of intermediate species have been made on a variety of transition metals, and especially on Pt, with emphasis on the Pt(lll) surface. Techniques such as TPD (temperature-programmed desorption), SIMS, NEXAFS (see Table VIII-1) and RAIRS (reflection absorption infrared spectroscopy) have been used, as well as all kinds of isotopic labeling (see Refs. 286 and 289). On Pt(III) the surface is covered with C2H3, ethylidyne, tightly bound to a three-fold hollow site, see Fig. XVIII-25, and Ref. 290. A current mechanism is that of the figure, in which ethylidyne acts as a kind of surface catalyst, allowing surface H atoms to add to a second, perhaps physically adsorbed layer of ethylene this is, in effect, a kind of Eley-Rideal mechanism. 

A solution of 0.60 mol of ethyllithium (note 1) in about 400 ml of diethyl ether (see Chapter II, Exp. 1) was added in 30 min to a mixture of 0.25 mol of 1,4-diethoxy-2-butyne (see Chapter VIII-6, Exp. 8) and 100 ml of dry diethyl ether. The temperature of the reaction mixture was kept between -40 and -45°C. Fifteen minutes after the addition had been completed, 0.5 mol of methyl iodide was added at -40 C, then 100 ml of dry HMPT (for the purification see ref. 1) were added dropwise in 15 min while keeping the temperature at about -40°C. Thirty minutes after this addition the cooling bath was removed, the temperature was allowed to rise and stirring was continued for 3 h. The mixture was... 

A mixture of 0.10 mol of freshly distilled 3-methyl-3-chloro-l-butyne (see Chapter VIII-3, Exp. 5) and 170 ml of dry diethyl ether was cooled to -100°C and 0.10 mol of butyllithium in about 70 ml of hexane was added at this temperature in 10 min. Five minutes later 0.10 mol of dimethyl disulfide was introduced within 1 min with cooling betv/een -100 and -90°C. The cooling bath vjas subsequently removed and the temperature was allowed to rise. Above -25°C the clear light--brown solution became turbid and later a white precipitate was formed. When the temperature had reached lO C, the reaction mixture was hydrolyzed by addition of 200 ml of water. The organic layer and one ethereal extract were dried over potassium carbonate and subsequently concentrated in a water-pump vacuum (bath... 

In the flask were placed 40 ml of ethanol, 10 ml of water, 12 g of finely powdered CuCN and 0.40 mol of 3-bromo-l-butyne (compare VIII-2, Exp. 3). The mixture was warmed to 55°C and a solution of 26 g of KCN in 60 ml of water was added drop-wise or in small portions care was taken that complete dissolution of the copper cyanide did not occur (note 2). The temperature of the mixture was maintained close to 60°C throughout the period of addition. The conversion was terminated... 

To a suspension of a tinc-copper couple in 150 ml of 100 ethanol, prepared from 80 g of zinc powder (see Chapter II, Exp. 18), was added at room temperature 0.10 mol of the acetylenic chloride (see Chapter VIII-2, Exp. 7). After a few minutes an exothermic reaction started and the temperature rose to 45-50°C (note 1). When this reaction had subsided, the mixture was cooled to 35-40°C and 0,40 mol of the chloride was added over a period of 15 min, while maintaining the temperature around 40°C (occasional cooling). After the addition stirring was continued for 30 min at 55°C, then the mixture was cooled to room temperature and the upper layer was decanted off. The black slurry of zinc was rinsed five times with 50-ml portions of diethyl ether. The alcoholic solution and the extracts were combined and washed three times with 100-ml portions of 2 N HCl, saturated with ammonium chloride. 

A polyether-amide with a heat distortion temperature of 198°C has been prepared by Hitachi by interfacial polycondensation of 2,2-bis-[4-(4-aminophen-oxy)phenyl]propane (VIII) with a mixture of isophthaloyl- and terephthaloyl-chloride (IX and X) (Figure 18.29). 

While this work was in progress Spath and Bretschneider showed that strychnine, on oxidation with permanganate in alkaline solution, furnished W-oxalylanthranilic acid (VII), brucine yielding oxalyl-4 5-dimethoxy-anthranilic acid, the latter observation providing confirmation of the evidence previously adduced that the two methoxy-groups in brucine are in the oj Ao-position relative to each other as indicated by Lions, Perkin and Robinson. The results so far considered indicate the presence in brucine and strychnine of the complex (VIII), which can be extended to (IX) if account is taken of the readiness with which carbazole can be obtained from strychnine and brucine and certain of their derivatives by decomposition with alkali at temperatures ranging from 200° to 400°, Knowledge of the structure of the rest of the molecule is mainly due to the results of the exhaustive study by Leuchs and his pupils of the oxidation... 

Many of the high-pressure forms of ice are also based on silica structures (Table 14.9) and in ice II, VIII and IX the protons are ordered, the last 2 being low-temperature forms of ice VII and III respectively in which the protons are disordered. Note also that the high-pressure polymorphs VI and VII can exist at temperatures as high as 80°C and that, as expected, the high-pressure forms have substantially greater densities than that for ice I. A vitreous form of ice can be obtained by condensing water vapour at temperatures of — 160°C or below. 

The available data are arranged by ring and ring-position in Tables II-VIII. The rate coefficients have been recalculated to the same units, where necessary the fact that different temperatures of reference were used in the publications should be noted. The temperatures used experimentally for a given substrate were chosen for a rate of reaction which was convenient to measure, and then for comparison, rate constants were calculated at a common temperature by means of the standard equations (cf. discussions by Ingold and by... 

VIII. Energy required to heat the spent catalyst from its reactor to the regenerator temperature =... 

Catalysts. The methanation of CO and C02 is catalyzed by metals of Group VIII, by molybdenum (Group VI), and by silver (Group I). These catalysts were identified by Fischer, Tropsch, and Dilthey (18) who studied the methanation properties of various metals at temperatures up to 800°C. They found that methanation activity varied with the metal as follows ruthenium > iridium > rhodium > nickel > cobalt > osmium > platinum > iron > molybdenum > palladium > silver. 

---