Surface nonionic

After reviewing various earlier explanations for an adsorption maximum, Trogus, Schechter, and Wade [244] proposed perhaps the most satisfactory one so far (see also Ref. 243). Qualitatively, an adsorption maximum can occur if the surfactant consists of at least two species (which can be closely related) what is necessary is that species 2 (say) preferentially forms micelles (has a lower CMC) relative to species 1 and also adsorbs more strongly. The adsorbed state may also consist of aggregates or hemi-micelles, and even for a pure component the situation can be complex (see Section XI-6 for recent AFM evidence of surface micelle formation and [246] for polymeric surface micelles). Similar adsorption maxima found in adsorption of nonionic surfactants can be attributed to polydispersity in the surfactant chain lengths [247], Surface-active impuri-... 

Low molecular cationic polymers or alum can also be used to flocculate pitch, ie, bind up the pitch so that it is retained in the sheet, to minimize pitch deposition on machine surfaces and fabrics (35,36). Alum is used commonly in newsprint operations (34). The addition of a nonionic surfactant with a hydrocarbon solvent to the wet end has shown some utility in preventing deposits of adhesive recycled furnish contaminants from forming on the paper... 

The higher aUphatic amine oxides are commercially important because of their surfactant properties and are used extensively in detergents. Amine oxides that have surface-acting properties can be further categorized as nonionic surfactants however, because under acidic conditions they become protonated and show cationic properties, they have also been called cationic surfactants. Typical commercial amine oxides include the types shown in Table 1. 

Sorption of nonionic, nonpolar hydrophobic compounds occurs by weak attractive interactions such as van der Waals forces. Net attraction is the result of dispersion forces the strength of these weak forces is about 4 to 8 kj/mol ( 1 2 kcal/mol). Electrostatic interactions can also be important, especially when a molecule is polar in nature. Attraction potential can develop between polar molecules and the heterogeneous sod surface that has ionic and polar sites, resulting in stronger sorption. 

Physical and ionic adsorption may be either monolayer or multilayer (12). Capillary stmctures in which the diameters of the capillaries are small, ie, one to two molecular diameters, exhibit a marked hysteresis effect on desorption. Sorbed surfactant solutes do not necessarily cover ah. of a sohd iaterface and their presence does not preclude adsorption of solvent molecules. The strength of surfactant sorption generally foUows the order cationic > anionic > nonionic. Surfaces to which this rule apphes include metals, glass, plastics, textiles (13), paper, and many minerals. The pH is an important modifying factor in the adsorption of all ionic surfactants but especially for amphoteric surfactants which are least soluble at their isoelectric point. The speed and degree of adsorption are increased by the presence of dissolved inorganic salts in surfactant solutions (14). 

Surface-active agents iacrease the conductivity of oils quite significantly (97), and addition of water, probably dissolved at the iaterface with the surfactant, further iacreases the conductivity. Nonionic and cationic surface-active agents are preferred to anionic surface-active agents probably because of their higher solubiHty ia oils and higher hygroscopicity. Many anionic surfactants have adequate antistatic efficiency, but they are used less frequendy. 

Properties. MethylceUulose [9004-67-5] (MC) and its alkylene oxide derivatives hydroxypropylmethylceUulose [9004-65-3] (HPMC), hydroxyethylmethylceUulose [9032-42-2] (HEMC), and hydroxybutyknethylcellulose [9041-56-9] (HBMC) are nonionic, surface-active, water-soluble polymers. Each type of derivative is available in a range of methyl and hydroxyalkyl substitutions. The extent and uniformity of the methyl substitution and the specific type of hydroxyalkyl substituent affect the solubifity, surface activity, thermal gelation, and other properties of the polymers in solution. 

Properties. Hydroxypropylcellulose [9004-64-2] (HPC) is a thermoplastic, nonionic cellulose ether that is soluble in water and in many organic solvents. HPC combines organic solvent solubiUty, thermoplasticity, and surface activity with the aqueous thickening and stabilising properties characteristic of other water-soluble ceUulosic polymers described herein. Like the methylceUuloses, HPC exhibits a low critical solution temperature in water. 

Furthermore, in a series of polyoxyethylene nonylphenol nonionic surfactants, the value of varied linearly with the HLB number of the surfactant. The value of K2 varied linearly with the log of the interfacial tension measured at the surfactant concentration that gives 90% soil removal. Carrying the correlations still further, it was found that from the detergency equation of a single surfactant with three different polar sods, was a function of the sod s dipole moment and a function of the sod s surface tension (81). 

---