Stripping strength

Peel strength (stripping Peel or Stripping Strength of Adhesive Bonds, Test for (D 903) strength) Climbing Drum Peel Test for Adhesives, Method for (D 1781)... 

There are two methods available for aroma recovery. In one method, a portion of the water is stripped from the juice prior to concentration and fractionally distilled to recover a concentrated aqueous essence solution. Apple juice requires 10% water removal, peach 40%, and Concord grape 25—30% to remove volatile flavor as an essence. Fractional distillation affords an aqueous essence flavor solution of 100—200-fold strength, which means the essence is 100 to 200 times more concentrated in flavor than the starting juice. A second method of essence recovery is to condensate the volatiles from the last effect of the evaporator they are enriched in volatile flavor components (18). 

Polyimides of 6FDA and aUphatic diamines with good low temperature processkig and low moisture swelling are known to be useful as hot-melt adhesives (109). Aluminum strips bonded by this polymer (177°C/172 kPa (25 psi) for 15 min) exhibited a lap-shear strength of 53 MPa (7690 psi) at room temperature and 35 MPa (5090 psi) at 100°C. The heat- and moisture-resistant 6F-containing Pis useful ki electronic devices are prepared from... 

Owing to the cycHc nature of the TBRC operation, waste heat recovery from the off-gases is not practical and the SO2 content of the gas varies with the converter cycle. In order to supply a relatively uniform flow and strength SO2 gas to a sulfuric acid plant, a system has been installed at RonnskAr whereby the SO2 from fluctuating smelter gases is partially absorbed in water. During smelter gas intermption, SO2 is stripped with air and the concentrated gas deflvered to the acid plant. 

Wrought lead—calcium—tin alloys contain more tin, have higher mechanical strength, exhibit greater stabiUty, and are more creep resistant than the cast alloys. RoUed lead—calcium—tin alloy strip is used to produce automotive battery grids in a continuous process (13). Table 5 Hsts the mechanical properties of roUed lead—calcium—tin alloys, compared with lead—copper and roUed lead—antimony (6 wt %) alloys. 

Load bend fatigue strength of alloys capable of withstanding 4—5 cycles before failure in 0—90—0 degree cycles, which is above the three-cycles-to-failure minimum in MIL-S l D-883 values pertain to a 0.25-mm thick strip that has been sheared to 0.45-mm width. 

The bottoms from the stripper (40—60 wt % acid) are sent to an acid reconcentration unit for upgrading to the proper acid strength and recycling to the reactor. Because of the associated high energy requirements, reconcentration of the diluted sulfuric acid is a cosdy operation. However, a propylene gas stripping process, which utilizes only a small amount of added water for hydrolysis, has been described (63). In this modification, the equiUbrium quantity of isopropyl alcohol is stripped so that acid is recycled without reconcentration. Kquilibrium is attained rapidly at 50°C and isopropyl alcohol is removed from the hydrolysis mixture. Similarly, the weak sulfuric acid process minimizes the reconcentration of the acid and its associated corrosion and pollution problems. 

This reaction can also be mn in a continuous fashion. In the initial reactor, agitation is needed until the carbon disulfide Hquid phase reacts fully. The solution can then be vented to a tower where ammonia and hydrogen sulfide are stripped countercurrendy by a flow of steam from boiling ammonium thiocyanate solution. Ammonium sulfide solution is made as a by-product. The stripped ammonium thiocyanate solution is normally boiled to a strength of 55—60 wt %, and much of it is sold at this concentration. The balance is concentrated and cooled to produce crystals, which are removed by centrifiigation. 

Empirical attempts have been made to relate strip and grab test results, particularly for cotton fabrics, so that if one strength is known, the other can be calculated. The relationship is complex, depending on fiber strength and modulus, yam size and crimp, yam-to-yam friction, fabric cover factor, weave, weight, and other factors (19). 

Zinc Costing of Ca.pa.citors, In the zinc coating of paper strip for capacitors, the paper strip is fed from air through locks into a vacuum environment. There, it is coated by thermally evaporated zinc. The rate of evaporation is so high that contamination of the zinc vapor is excluded. The paper is fed at the maximum rate permitted by its own strength. 

---