Stable parameters

Tests performed on humans and animals under normal and pathological conditions showed that under normal conditions the ACW is a stable parameter specific to species and age. On the contrary it is very sensitive to any stress factors (bacterial and sterile inflammations, surgical and psychoemotional stress) and to the application of P-agonists [33],... 

In pure circuit theory, the velocity of circulation can be regarded as too orthodox a concept, partly due to the unrealistic quantity theory assumption that it is a stable parameter. However, in an implicit defence of the velocity concept, Graziani (2003 12) has denigrated the extreme case of an undefined, infinite velocity as being associated with a quasi-barter economy in which money did not exist . 

Note that a d-SoC is defined by the stable parameters of the pattern that constitute it, not by the particular technique of inducing that pattern. Cback)... 

According to the main idea, the autonomous wind-hydrogen station (AWHS) should be adapted to the conditions when a single consumer of the produced electric power is an electrolyser, which does not require standard stable parameters of power supply for its normal operation. To realise this idea, two main problems have to be addressed in the course of the development of the AWHS. 

Cut points specify the beginning and end of the collection of a fraction. Cut points can be based on time, although in practice time is not the most stable parameter, due to possible fluctuations in the flow rate. They can be based on threshold values of the UV-detector signal or on volume of eluent through a mass flowmeter. Cut point locations can also be a combination of a characteristic feature on the chromatogram and volume. Cut point locations for valve switching may also be based on the response of less traditional detection instrumentation such as the on- line measurement of density, conductivity, temperature, spedflc ion detection, near infrared, or refractive index. 

Such a function may be included into a structurally stable parameter--dependent family of functions which will be considered to be a potential function. The state of a physical system will be determined from the condition of the minimum of a potential function having a degenerate critical point, defining the catastrophe surface M. 

According to Eqn (8.1) the light-emission efficiency is related only to the core radius and bending radius of the POF. For a single variety of POF, the numerical aperture and the refractive index of the cladding are the stable parameters (Wang et al., 2013). 

It has been discussed earlier that for the development of various acoustoelectronic devices with the thermo-stable parameters, it is possible to use the thermo-stable... 

This technology provides robust and stable parameters. Over the years, a significant optimization potential was achieved in all process steps as well as in equipment and machinery. 

The results of the comparative analysis in terms of changes in flaw length and maximum height are shown in Fig. 3. As can be seen the flaw parameters are stable, and the height maximum increase (2 mm) correlates with the AUGUR4.2 precision of linear measurements. 

To operate the MPI or LPI equipment at stable and reprodncable inspection conditions modern units are equipped with a monitoring and control system called "Quality Assurance Package" (termed QAP). The QAP System is ba.sed on an industrial PC with a bus system and field sensors. It ensures that process parameters important for the reproducability of the MPI or LPI are controlled an held between defined limits by a central computer system. It can be adapted to any old system, as well as integrated into new systems. 

If the inspection equipment can be run under stable and reproducable conditions due to the QAP the basis for using a camera system for flaw detection is given.The camera system consists of CCD-cameras and a pattern recognition software. Up to four CCD-cameras can be served by one PC. One shot of the part may be copied up to 16 times in the computer and this theoretically enables the crack determination with 16 different parameter sets. 

For the kind of transition above which the order parameter is zero and below which other values are stable, the coefficient 2 iiiust change sign at the transition point and must remain positive. As we have seen, the dependence of s on temperature is detemiined by requiring the free energy to be a miniimuii (i.e. by setting its derivative with respect to s equal to zero). Thus... 

Figure A3.3.2 A schematic phase diagram for a typical binary mixture showmg stable, unstable and metastable regions according to a van der Waals mean field description. The coexistence curve (outer curve) and the spinodal curve (iimer curve) meet at the (upper) critical pomt. A critical quench corresponds to a sudden decrease in temperature along a constant order parameter (concentration) path passing through the critical point. Other constant order parameter paths ending within tire coexistence curve are called off-critical quenches.

McMillan s model [71] for transitions to and from tlie SmA phase (section C2.2.3.2) has been extended to columnar liquid crystal phases fonned by discotic molecules [36, 103]. An order parameter tliat couples translational order to orientational order is again added into a modified Maier-Saupe tlieory, tliat provides tlie orientational order parameter. The coupling order parameter allows for tlie two-dimensional symmetry of tlie columnar phase. This tlieory is able to account for stable isotropic, discotic nematic and hexagonal columnar phases. 

Figure C3.6.5 The first two periodic orbits in the main subhannonic sequence are shown projected onto the (c, C2) plane. This sequence arises from a Hopf bifurcation of the stable fixed point for the parameters given in the text. The arrows indicate the direction of motion, (a) The limit cycle or period-1 orbit at k 2 = 0.11. (b) The first subhannonic or period-2 orbit at k 2 = 0.095.

The typical dependence of the stable stationary solutions to (4) on the control parameter of the model Xe is presented in Fig. 1. These results have been obtained as numerical solutions of (4) with equal to... 

Fig. 1. The dependence of the stable stationary values of the adsorption and conformational variables on the control parameter, Xe. a-total adsorption per the mole of the nucleotides, b-the probability of finding of an arbitrary NA unit in the A form, c-the probability of finding of an arbitrary NA unit in the B-form. Param-(ders values used to obtain numerical results Vmi = 3,nL = 15.4, = 3.24,6° =...

Fig. 2. The dependence of the stable stationary values of the adsorption and conformational variables on the control parameter, for 0 < < 0.9. a-total adsorption...

IlypcrChem cannot perform a geometry optinii/.aiioii or molecular dynamics simulation using Cxien ded Iliickel. Stable molecules can collapse, with nuclei piled on top of one another, or they can dissociate in to atoms. With the commonly used parameters, the water molecule is predicted to be linear. 

---