Smearing

Four mechanisms have been suggested to explain how faults provide seals. The most frequent case is that of clay smear and juxtaposition (Fig. 5.8)... 

Clay smear soft clay, often of marine origin, is smeared into the fault plane during movement and provides an effective seal. 

Figure 5.8 Fault seal as a result of clay smear and juxtaposition...

Some general points are the following. One precondition for a vertical step in an isotherm is presumably that the surface be sufficiently uniform that the transition does not occur at different pressures on different portions, with a resulting smearing out of the step feature. It is partly on this basis that graphitized carbon, BN, MgO, and certain other adsorbents have been considered to have rather uniform surfaces. Sharp LEED patterns are another indication. 

The disc contains a hole, centrally placed, through which a small glass stirrer can be pushed. The stirrer should be smeared with a very small amount of silicone grease where it passes through the spring disc. A relatively powerful motor is required for this apparatus. 

A smear head causes less stagnation and overpacking than a nonreturn valve. A conventional-type reverse-tapered nozzle with the bore as large as possible without sudden changes in diameter is preferred. Independently controlled, zone-type heaters for heating the nozzle and at least two zones on the cylinder are used. 

Printed circuit boards manufacture is aided by the use of KMnO. Alkaline permanganate solution is used to remove resin smeared on the interior hole wall of multilayered printed circuit boards. Additionally the hole wall is etched, resulting in a surface with excellent adhesion characteristics, for electrodeless copper (250). The alkaline permanganate etchback system containing >60 g/L KMnO and 40-80 g/L NaOH at 70—80°C, is effective for difunctional, tetrafiinctional, and polyimide resin substrates, where the level of etchback is direcdy proportional to the immersion time (10—20 min) (251). 

Chemical modification of the wax can improve smear resistance (5). Sihcones, which do not harm furniture finishes (6), are incorporated as film-forming ingredients in furniture pohshes. The lubricant properties of sihcones improve ease of apphcation of the pohsh and removal of insoluble soil particles. In addition, sihcones make dry films easier to buff and more water-repeUent, and provide depth of gloss, ie, abihty to reflect a coherent image as a result of a high refractive index (7). Wax-free pohshes, which have sihcones as the only film former, can be formulated to dehver smear resistance (8). Another type of film former commonly used in oil-base furniture pohshes is a mineral or vegetable oil, eg, linseed oil. 

The short-range order in a material is important in determining optoelectronic properties. For instance, x-ray and electron diffraction experiments performed on amorphous siHcon (i -Si) and germanium (a-Ge) have revealed that the nearest neighbor environments are approximately the same as those found in their crystalline counterparts (6) photoemission experiments performed on i -Si show that the DOS in valence and conduction bands are virtually identical to the corresponding crystal with the exception that the singularities (associated with periodicity) present in the latter are smeared out in the former. 

Step 11. At this point a computer program refines the atomic parameters of the atoms that were assigned labels. The atomic parameters consist of the three position parameters x,j, and for each atom. Also one or six atomic displacement parameters that describe how the atom is "smeared" (due to thermal motion or disorder) are refined for each atom. The atomic parameters are varied so that the calculated reflection intensities are made to be as nearly equal as possible to the observed intensities. During this process, estimated phase angles are obtained for all of the reflections whose intensities were measured. A new three-dimensional electron density map is calculated using these calculated phase angles and the observed intensities. There is less false detail in this map than in the first map. 

A widely used instmment for air monitoring is a type of ionization chamber called a Kaimn chamber. Surface contamination is normally detected by means of smears, which are simply disks of filter paper wiped over the suspected surface and counted in a windowless proportional-flow counter. Uptake of tritium by personnel is most effectively monitored by urinalyses normally made by Hquid scintillation counting on a routine or special basis. Environmental monitoring includes surveillance for tritium content of samples of air, rainwater, river water, and milk. 

---