Single metal surface site

To what extent is the macroscopic proton release the direct expression of the metal/surface site reactions Table V compares the macroscopic proton coefficients (Xp ) ) with the coefficient expected if only the Cd(II) surface reactions are considered is the proton coefficient determined by considering the mole fraction of Cd(II) surface species and their formation reactions (Figure 14b). For example, when pSOH is 2.84, y = 0.11 x 1 + 0.89 x 2 = 1.89. At high alumina concentrations pSOH 2.14-2.53) the single surface reaction required to fit the data sets a limiting proton release of 2.0. 

These data indicate that sulfur preferentiaUy adsorbs on sites of lowest coordination. Different types of sulfur adsorption were also observed by the Berkeley group on Mo 100 single metal surfaces. deposited on... 

Monovalent anion adsorption on metal oxide surfaces from aqueous solution is similar to monovalent cation adsorption in that it can be assumed that a single anion— surface site complex is the predominant surface complex formed. The obvious difference is that anions adsorb on cationic surface sites, unlike cations, which adsorb on anionic surface sites. The chemical reactions creating the monovalent anion—surface site complex are depicted in Fig. 17. 

Figure Bl.22.1. Reflection-absorption IR spectra (RAIRS) from palladium flat surfaces in the presence of a 1 X 10 Torr 1 1 NO CO mixture at 200 K. Data are shown here for tluee different surfaces, namely, for Pd (100) (bottom) and Pd(l 11) (middle) single crystals and for palladium particles (about 500 A m diameter) deposited on a 100 A diick Si02 film grown on top of a Mo(l 10) single crystal. These experiments illustrate how RAIRS titration experiments can be used for the identification of specific surface sites in supported catalysts. On Pd(lOO) CO and NO each adsorbs on twofold sites, as indicated by their stretching bands at about 1970 and 1670 cm, respectively. On Pd(l 11), on the other hand, the main IR peaks are seen around 1745 for NO (on-top adsorption) and about 1915 for CO (tlueefold coordination). Using those two spectra as references, the data from the supported Pd system can be analysed to obtain estimates of the relative fractions of (100) and (111) planes exposed in the metal particles [26].

The catalysts with the simplest compositions are pure metals, and the metals that have the simplest and most uniform surface stmctures are single crystals. Researchers have done many experiments with metal single crystals in ultrahigh vacuum chambers so that unimpeded beams of particles and radiation can be used to probe them. These surface science experiments have led to fundamental understanding of the stmctures of simple adsorbed species, such as CO, H, and small hydrocarbons, and the mechanisms of their reactions (42) they indicate that catalytic activity is often sensitive to small changes in surface stmcture. For example, paraffin hydrogenolysis reactions take place rapidly on steps and kinks of platinum surfaces but only very slowly on flat planes however, hydrogenation of olefins takes place at approximately the same rate on each kind of surface site. 

Of these, the most extensive use is to identify adsorbed molecules and molecular intermediates on metal single-crystal surfaces. On these well-defined surfaces, a wealth of information can be gained about adlayers, including the nature of the surface chemical bond, molecular structural determination and geometrical orientation, evidence for surface-site specificity, and lateral (adsorbate-adsorbate) interactions. Adsorption and reaction processes in model studies relevant to heterogeneous catalysis, materials science, electrochemistry, and microelectronics device failure and fabrication have been studied by this technique. 

This treatment assumes that diffusion of the solute to the surface is not ratecontrolling, which will generally be true. It also assumes that all surface sites are equivalent, which is often not so. For example, different surface planes of single metal crystals have been shown to have markedly different activities. 

The aldehyde oxidoreductase from Desulfovibrio gigas shows 52% sequence identity with xanthine oxidase (199, 212) and is, so far, the single representative of the xanthine oxidase family. The 3D structure of MOP was analyzed at 1.8 A resolution in several states oxidized, reduced, desulfo and sulfo forms, and alcohol-bound (200), which has allowed more precise definition of the metal coordination site and contributed to the understanding of its role in catalysis. The overall structure, composed of a single polypeptide of 907 amino acid residues, is organized into four domains two N-terminus smaller domains, which bind the two types of [2Fe-2S] centers and two much larger domains, which harbor the molybdopterin cofactor, deeply buried in the molecule (Fig. 10). The pterin cofactor is present as a cytosine dinucleotide (MCD) and is 15 A away from the molecular surface,... 

Ethylene, C2H4, can adsorb in two modes the weaker Jt-bonded ethylene, in which the C=C double bond is above a single metal atom, or the stronger di-cr bonded ethylene in which the two C-atoms of the ethylene molecule bind to two metal atoms (Fig. 6.37). We consider the (111) metal surface. Hydrogen adsorbs dis-sociatively and is believed to reside in the threefold hollow sites of the metal. 

The nucleation behavior of transition metal particles is determined by the ratio between the thermal energy of the diffusing atoms and the interaction of the metal atoms at the various nucleation sites. To create very small particles or even single atoms, low temperatures and metal exposures have to be used. The metal was deposited as metal atoms impinging on the surface. The metal exposure is given as the thickness (in monolayer ML) of a hypothetical, uniform, close-packed metal layer. The interaction strength of the metals discussed here was found to rise in the series from Pd < Rh < Co ( Ir) < V [17,32]. Whereas Pd and Rh nucleate preferentially at line defects at 300 K and decorate the point defects at 90 K, point defects are the predominant nucleation center for Co and V at 300 K. At 60 K, Rh nucleates at surface sites between point defects [16,33]. 

In conclusion, hydrogenolysis processes and coke formation occur on large ensembles of surface platinum atoms [160], while dehydrogenation reactions would proceed on single (isolated) Pt atoms [169]. The presence of tin atoms regularly distributed on the metal surface diminishes the size of the ensemble [130,170-173], the same is observed for copper atoms on nickel surfaces [174] or tin atoms on rhodium and nickel surfaces [137,175-177], leading to site isolation and therefore to selectivity. 

---