Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Silicone Rubber Sponge

Three types of silicone foams are discussed briefly below — silicone elastomeric foams, silicone rubber sponge, and room-tempera-ture-foaming silicone rubbers. [Pg.249]

The apparatus was separated into two compartments(A,B) with a silicone rubber sponge sheet which had a hole in the middle to hold fish at just the back of pectoral fin. Both the head and rear parts of fish were covered with two small boxes which had many holes and were fixed to a cover plate of the apparatus. PCP-free water was supplied into the head compartment(A) at a flow rate of 1 liter/h and the overflow from (A) was reserved in an ice-cooled tank for the analysis of PCP excreted from gills. Fish urine was led by a cannula to an ice-cooled flask through... [Pg.134]

AMS 3193-B-85 Silicone Rubber Sponge, Closed Cell, Medium, Extreme Low Temperature, 6 pp (DOD Adopted) (FSC 9320) (AS)... [Pg.422]

Silicon Rubber Sponge Rubber Styrene-acrylonitrile (SAN) Styrene-butadiene copolymers (SBR) Urea-formaldehyde (Cellulose filled)... [Pg.38]

MIL-R-46089B(MR) Rubber Sponge, Silicone Closed Cell, 12 February 1981, 7 pp (FSC 9320) (MR)... [Pg.432]

Cohrlastic, Silicone rubber sheet and sponge foam, CHR Div. of Furon Co. [Pg.898]

ROMANOWSKi R and JONES B A, New technology to produce silicone sponge without chemical blowing agents or volatile organics. Rubber Division, American Chemical Society, Cleveland, American Chemical Society, 2003. [Pg.301]

Notice 1 states that the specification is currently valid for use in acquisition. The original date of the base specification was 25 June 1982. The cushions are intended for use in assembly of rocket motors for M753, 8-inch projectiles. Type I covers soft-grade silicone sponge rubber and Type II medium-grade silicone sponge rubber. [Pg.435]

In the rubber industry, moisture absorbed on the surface of silicate, impacts the rate and extent of cure and results in sponge-like textures. In moisture cured systems such as polyurethanes, polysulfides and silicones, moisture causes a premature reduction in shelf-life. In extrusion and injection molding the moisture absorbed on fillers contributes to various defects and a strict regime must be followed regarding the drying time and the conditions prior to processing. Lacing, a less well known phenomenon, is caused by the absorption of moisture on the surface of titanium dioxide. ... [Pg.278]

COHRlastic . [CHR Industries/Furon] Silicone elastomers, some glass-reinforced, aluminum/rubber composites, silicone sponge rubber dimensionally stable, flexible fabric and molded sheet for belting, vacuum blankets, thermal shielding applies. [Pg.81]

Chem. Descrip. Activated azodicarbonamide CAS 123-77-3 EINECS/ELINCS 204-650-8 Uses Chemical foaming agent for silicone sponge rubber Features Nonstaining does not interfere with peroxide cure decomp, range 140-150 C... [Pg.228]

Mikrofine TSH p-Tolylsulfonyl hydrazine foam builder, chemical silicone sponge rubber... [Pg.2718]

See other pages where Silicone Rubber Sponge is mentioned: [Pg.249]    [Pg.250]    [Pg.357]    [Pg.249]    [Pg.250]    [Pg.357]    [Pg.296]    [Pg.149]    [Pg.667]    [Pg.741]    [Pg.742]    [Pg.885]    [Pg.7607]    [Pg.665]    [Pg.743]    [Pg.818]    [Pg.34]    [Pg.732]    [Pg.806]    [Pg.807]    [Pg.672]    [Pg.819]   


SEARCH



Rubber siliconization

Silicon rubbers

Silicone rubbers

Silicones silicone rubbers

Siliconized rubber

Sponge rubber

Sponges

© 2024 chempedia.info