Silicon complexes with chromium

The silicon-metal doubly bonded compounds can further react to yield desired derivatives. Recently, vinyl magnesium bromide was reported to react with chloro complexes containing chromium or iron double bonds to silicon, to yield the l-metalla-2-sila-l,3-diene compounds (115, equation 34), which can potentially be used to functionalize silicon polymers in a desired fashion121. 

Alkynyl complexes. These complexes, which are readily available by reaction of an alkynyllithium with chromium carbonyl followed by methylation with CH3OSO2F, undergo facile Diels-Alder reactions with dienes to provide a general route to ,p-un-saturated chromium carbene complexes. The latter undergo benzannelation or cyclo-hexadienone annelation on reaction with an alkyne. A (trimethylsilyl)ethynyl complex is useful because benzannelation results in migration of silicon from carbon to oxygen to provide a protected phenol. 

Fischer-type carbenes are known as potential carbene transfer reagents to electron-rich and electron-deficient alkenes. Little is known about the chemistry of carbene complexes with silicon substituents at the carbene C-atom, whereas complexes with germanium, tin, or lead have not yet been prepared. The tungsten-carbene complexes 6 react with an excess of ethyl vinyl ether to give l,2-diethoxy-l-(trialkylsilyl)cyclopropanes 7." Only the f-isomers were formed and similar results can be achieved by using the corresponding molybdenum or chromium complexes. On the other hand, no reaction takes place with 2,3-dihydrofuran or ethyl ( )-but-2-enoate. ... 

HYDRIDO-SILYL COMPLEXES OF CHROMIUM WITH METAL-HYOROGEN-SILICON THREE-CENTER BONDS... 

Sihcone products dominate the pressure-sensitive adhesive release paper market, but other materials such as Quilon (E.I. du Pont de Nemours Co., Inc.), a Werner-type chromium complex, stearato chromic chloride [12768-56-8] are also used. Various base papers are used, including polyethylene-coated kraft as well as polymer substrates such as polyethylene or polyester film. Sihcone coatings that cross-link to form a film and also bond to the cellulose are used in various forms, such as solvent and solventless dispersions and emulsions. Technical requirements for the coated papers include good release, no contamination of the adhesive being protected, no blocking in roUs, good solvent holdout with respect to adhesives appHed from solvent, and good thermal and dimensional stabiUty (see Silicon COMPOUNDS, silicones). 

The high-chromium irons undoubtedly owe their corrosion-resistant properties to the development on the surface of the alloys of an impervious and highly tenacious film, probably consisting of a complex mixture of chromium and iron oxides. Since the chromium oxide will be derived from the chromium present in the matrix and not from that combined with the carbide, it follows that a stainless iron will be produced only when an adequate excess (probably not less than 12% of chromium over the amount required to form carbides is present. It is commonly held, and with some theoretical backing, that carbon combines with ten times its own weight of chromium to produce carbides. It has been said that an increase in the silicon content increases the corrosion resistance of the iron this result is probably achieved because the silicon refines the carbides and so aids the development of a more continuous oxide film over the metal surface. It seems likely that the addition of molybdenum has a similar effect, although it is possible that the molybdenum displaces some chromium from combination with the carbon and therefore increases the chromium content of the ferrite. 

Attempts made to produce an alloy more resistant to hydrochloric acid have resulted in alloys containing 17-18% silicon or 14-5% silicon and chromium plus 3% molybdenum. The first is produced in Britain, and the second in the United States. The reason for the increase in resistance to hydrochloric acid of the Fe-18 Si alloy is thought to lie primarily in the increased density of the silica-rich film left on the metal by initial corrosion. The addition of 6% chromium with some molybdenum to Fe-14-5 Si causes the formation of extremely stable complex carbides with the consequent complete elimination of graphite plus the formation of a more penetration-resistant silica film, probably containing chromium in substantial quantity. 

Apart from the metal atom aggregation reactions described below, bis(arene)metal complexes of the early transition metals are resistant to ligand displacement The rings on the corresponding bis(naphthalene)metal species (41) are by, contrast, labile. Polymer-supported analogs of these naphthalene compounds with vanadium and chromium are known (42), but Ti atoms attack the polymer at the silicon ether linkage. These and other hybrid polymers can be further modified once the metal atom is incorporated. Thus a-methyl naphthalene is displaced from the hybrid organometallic polymer shown in Scheme 7 (43). 

---