Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Tubing shrink

The porous carbon rod is often the main pathway of escape for the gases formed in the cell. This pathway also allows ingress of oxygen to the cell limiting the shelf life of the system. The use of shrink tube outer wrapping and other devices have, however, improved the leakage property dramatically over prior generation cells. [Pg.522]

To try to separate the oxidation of adsorbate from that of bulk methanol, a droplet cell, shown in Fig. 3-2, was used. A working electrode, platiniun wire, is dipped into an electrolyte droplet on a capillary, which is then connected to the electrolyte reservoir. The top portion of the capillary was covered with Teflon FEP held by Teflon heat shrinking tube. The counter electrode, platinum wire, is in the capillary and its tip reaches just below the droplet. The reference electrode, R. H. E., is constructed between the reservoir and the droplet. [Pg.120]

Thin-walled (approximately 0.010-0.040 in., or 0.25-1.0 mm) tubing is usually selected by continuous service temperature, which may range from 90°C (194°F) for some PVC tubing up to 250°C (482°F) for tubing made from PTFE. The main use of thin shrink tubing is in electrical and electronic applications. [Pg.198]

Heat shrink sheets are used for many of fhe same applications as heavy wall shrink tubing. The advantage of the sheet over a tube is that it can be conveniently slipped over the area to be protected, for example, over continuously installed cable. There are many methods to close the heat-shrinkable sheets, such as zippers, rail and channel, heat-sealable bonds, etc., some of them patented. ... [Pg.201]

Essentially, two methods are used to produce shrink tubing from an extruded tube. One involves expanding the tube, which was cross-linked by radiation and heated to temperatures above its crystalline melting point, into a sizing tool. The diameter of the sizing tool determines the amount of stretch. The stretched tubing... [Pg.166]

FIGURE 8.7 One method used to produce shrink tubing from an extruded tube, described in the original Raychem patent. [Pg.168]

The second method used to produce shrink tubing is designed to expand the tubing heated above its crystalline melting point into a stationary forming tube or mold, using air pressure. [Pg.169]

Electrical tape, liquid electrical tape, liquid rubber or shrink tube Hardware or electronics supplier ... [Pg.255]

Then remove any mold marks inside the box on the surface where the connector block will be glued. Place the connector block inside the box to determine the position for the take off holes in the plastic box. Also, figure where the holes for the lead outlets to the electrolyzer will be. To choose an appropriate hole size, be sure to consider the width of the bus ribbon including shrink tube insulation. Outlet holes going to the electrolyzer should be sized for the wire used, plus additional space if... [Pg.48]

Put shrink tubing on the take off leads so that the leads are insulated from the metal backing of the panel. To do this, slip a piece of shrink tubing over both bus wire leads, hold it in its final position, and apply heat to shrink the tubes. [Pg.55]

Fittings, barbed fittings and unions from different suppliers or homemade devices are used to connect the components of the manifold. They should provide suitable linking conditions to avoid loss of the handled solutions and/or the ingress of air bubbles. Glue, heat shrink tubing and push fit connections are often used to guarantee a complete seal. A small... [Pg.228]

Desirable pol5mier for heat shrink tubing must be able to sustain a great degree of elongation and conversely return back to its pre-expansion dimen-... [Pg.208]


See other pages where Tubing shrink is mentioned: [Pg.353]    [Pg.197]    [Pg.197]    [Pg.13]    [Pg.166]    [Pg.126]    [Pg.158]    [Pg.160]    [Pg.207]    [Pg.253]    [Pg.419]    [Pg.424]    [Pg.337]    [Pg.199]    [Pg.242]    [Pg.55]    [Pg.325]    [Pg.166]    [Pg.229]    [Pg.208]    [Pg.208]    [Pg.208]    [Pg.208]    [Pg.208]    [Pg.208]    [Pg.442]   
See also in sourсe #XX -- [ Pg.208 ]

See also in sourсe #XX -- [ Pg.220 , Pg.221 ]




SEARCH



Heat Shrink Tubes

Heat shrink tubing

Shrinking

Shrinks

© 2024 chempedia.info