Section width

Typical Section Width, ft Typical Tube Length, ft... 

Pick a desirable combination of tube length and section width to achieve the approximate face area. 

Total volume of liquid in extraction section Width of channel perpendicular to screw flights in screw extruder... 

Figure 2. Plot of the cross-sectional width f(r) vs. radial distance r for an Yphantis centerpiece...

For the Yphantis cell one notes dv = hf(r)dr, where f(r) is the cross-sectional width. This will vary with r since the holes are curved at each end. A typical plot of f(r) vs. r is shown in Figure 2. For component i the conservation of mass equation is... 

In enamel and hypermineralized dentin more than 100 repeat periods were counted across one single crystal. However, in normal bone and dentin, individual crystals show fewer repeats, commonly less than 10 and as little as 4 this would correspond to a cross-sectional width of about 40 to 90 A360. The length of the crystals is in the range of a few 100 A. In summary, at least two morphologically distinct types of crystallites are present in bones and teeth, and the smaller-sized fraction represents the bulk of the mineral phase. 

A detailed analysis of the distributions of conversion, temperature and velocities was carried out126 using a model, which included the fountain effect at the front of the stream. A comparison of the results was made for molds of different geometrical form (plane cavity, cylindrical and disk-like shapes) for the same temperature, average output and cross-sectional width of the mold. It was established that the distribution of the degree of conversion is qualitatively the same in all these cases (Fig. 4.55). 

Figure 8.9 Atomic force microscopy images of nanostructures from the symmetrically substituted p4Ps NHP4, NMeP4, and CNP4. Height scales 150nm, 250nm, lOOnm, respectively. Cross-sections (width x height) show the respective dimensions.

Keep sections of multipart tables at similar widths. Widely divergent section widths within a table waste space and detract from general appearance. 

In continuum percolation (see Section 1.2.1(g)), we suppose that the defects are introduced in a solid sample as randomly placed insulating holes with the shape of a circle (in two dimensions) or a sphere (in three dimensions) and we include the possibility of overlap of the defects (Swiss cheese model). This last possibility gives near Pc an infinite cluster with the the links having different cross-sectional width 6. This property is essentially responsible for the differences between lattice and continuum percolations. 

Calculation of group diameter, dg. the cross-sectional width (group diameter) of a polar group of a collector can be calculated using the data for bond angle, covalent radius and the van der Walls radius of the compound. 

A typical size specification for passenger car tires is XXX/YY RZZ, where XXX is the cross-section width in millimeters, YY is the aspect ratio (of the cross-section height to its width) in percent, R is the abbreviation for radial construction and ZZ is the rim diameter in inches. By utilizing its size specification, the outside diameter and volume of a tire are estimated. The outside diameter, Dg (mm) can be expressed as... 

Aspect ratio A numerical term that expresses the relationship between tire section height and cross-section width. An aspect ratio of 70 indicates the tire section is approximately 70% as high as it is wide. 

Section width Width of a new tire section excluding side ribs, lettering, and decorations. 

Approximate section width in millimeters when mounted on the proper rim. 

Figure 41 Cartoon of local lamellar structure. The black and white patches represent cross sections of the surfactant + alcohol + oil layers and the water layers, respectively. The relative thicknesses of the water- and non-water-filled regions were chosen approximately according to the values of do and d for the 55 wt% water sample on the water dilution line W5 of Fig. 30b. The lamellae extend above and below the plane of the page. For simplicity, they are assumed to be perpendicular to the page, resulting in uniform cross-sectional widths. The inset shows a more detailed cartoon of the structure of the lamellar cross section as seen from above. (From Ref. 308.)...

Notch sensitivity is evaluated by considering a tensile specimen with a stress concentrating feature such as a hole. For an isotropic elastic tensile specimen with a circular hole of one half of the section width, as an example, linear elasticity theory predicts a maximum stress at the edge of the hole in the plate to be 2.15 times the average section stress... 

To test the impact strength, the sample is quickly bent under stress up to the breaking point. The impact can be a pendulum or a flexural or a tensile impact. To test the notched-bar impact strength, the sample is first notched distinctly, and the subsequent tensile strength, so to speak, is measured. The ratio of the work done to the cross-sectional width is termed the impact strength. 

---