Sand blast

In other useful appHcations, siHcon nitride bearings have been found to offer exceUent performance siHcon nitride cutting tool inserts are a commercial product wear parts such as sand blast nozzles, seals, and die liners are also commercially produced the superior performance of heat exchangers has been demonstrated and there are also military appHcations. 

For Type 2 pipettes the final drop of liquid remaining in the tip must be expelled, which is contrary to the usual procedure. Such pipettes are therefore distinguished by a white or sand-blasted ring near the top of the pipette. 

Although hardness is a somewhat nebulous term, it can be defined in terms of the tensile modulus of elasticity. From a more practical side, it is usually characterized by a combination of three measurable parameters (1) scratch resistance (2) abrasion or mar resistance and (3) indentation under load. To measure scratch resistance or hardness, an approach is where a specimen is moved laterally under a loaded diamond point. The hardness value is expressed as the load divided by the width of the scratch. In other tests, especially in the paint industry, the surface is scratched with lead pencils of different hardnesses. The hardness of the surface is defined by the pencil hardness that first causes a visible scratch. Other tests include a sand-blast spray evaluation. 

The metal plates to be coated with Raney nickel were type 304 stainless steel. Plate surfaces were prepared by sand blasting with an iron-free... 

Heavy dusts Heavy/wet sawdust, metal turnings, foundry tumbling barrels and shake-out, sand blast dust, wood blocks, brass turnings, cast iron boring dust, lead dust 4000-4500 20-23... 

Enclosure takes the concept of isolation still further. In this approach, the complete operation is physically enclosed by an impervious barrier, perhaps metal or plastic, with access allowed only occasionally by suitably protected maintenance workers or in emergencies. This approach might be found, for example, in sand-blasting operations, in conditions where there is a severe fume hazard, or perhaps, as seen in the cautionary tale about Jake Whitman, in a continuous lead-quenching bath operation. It should be noted that in most instances, exhaust ventilation of the enclosed area should also be undertaken. 

Abrasion to abrade the surface to eliminate oxides, etc. by mechanical means such as brushing, sanding, blasting, sandpapering. .. 

Concrete vessels were somewhat less prone to explosions sand blasting the surface reduced the incidence. 

The underlying mode of action, involving as it does the flow induced vibration of a steel blade, immediately suggests the problem of erosion by particulate matter - the sand blasting effect. Despite this apparent drawback a whistle has been used in this Scott Bader process over several years without blade replacement. 

Unless otherwise specified, the vendor shall commercially sand blast, in accordance with SSPC SP 6, all grout contact surfaces of the baseplate, and coat those surfaces with inorganic zinc silicate in preparation for epoxy grouting. 

Surface Tension Measurement. Surface tension was determined with a Rosano Tensiometer (Arenberg-Sage Inc., Jamaica Plain, Mass.) utilizing a sand-blasted platinum blade. 

The experimental apparatus employed was described elsewhere ( ). Briefly, surface pressures were determined continuously from surface tension measurements using a sand blasted platinum blade, suspended from a transducer-amplifier (Sandborn, model 311A). The transducer signal was fed to a X-Y recorder. Surface potential was measured with an electrometer (Kelthly, model 610B) using an air electrode coated with Ra and an Ag/AgCl electrode in the subsolution. 

Neoprene and nitrile rubbers (gum stocks) filled with silica are generally used for insulation of rocket motors and the general process consists of (i) sand blasting of rocket motor followed by cleaning with petrol or organic solvent and drying,... 

The surface trough was made of Lucite, 45 X 15 X 1.5 cm. and was divided into two compartments of equal size by a septum of Lucite, 1.5 cm. high. Cooling channels for temperature control were milled into the bottom of the trough. The monolayer was spread inside a paraffined mica frame which floated on the water and was firmly positioned by external mounts. The surface tension was measured with a double-hook torsion balance and a sand-blasted platinum Wilhemy plate. A Beckman model G pH meter with standard glass and KC1 electrodes was used to measure pH. 

---