Rotating construction

Chirp pulses have also been used in a double-J-modulated INEPT-INADE-QUATE.29 Universal rotators constructed by combining two point-to-point rotations30 have been recently used in 1H- and 13C-detected IPAP-INADEQUATE experiments.31,32... 

These electrodes are inserted into a rotator, constructed with a variable speed synchronous motor drive controlled by a feedback system sensing the rotational velocity. The velocity of rotation is controlled to 1%. 

The coin-tap test is a widely used teclinique on thin filament winded beams for detection of disbonded and delaminated areas. However, since the sensitivity of this teclinique depends not only on the operator but also on the thickness of the inspected component, the coin-tap testing technique is most sensitive to defects positioned near the surface of the laminate. Therefore, it was decided to constructed a new scaimer for automated ultrasonic inspection of filament winded beams. A complete test rig illustrated in figure 6 was constructed in order to reduce the scanning time. While the beam rotates the probe is moved from one end to the other of the beam. When the scarming is complete it is saved on diskette and can then be evaluated on a PC. The scanner is controlled by the P-scan system, which enables the results to be presented in three dimensions (Top, Side and End view). 

In those cases where stirring for short periods is necessary, this may usually be accomphshed by gentle rotation of the vessel thus imparting a swirhng motion to its contents. If the vessel cannot conveniently be moved, a hand-operated stirrer constructed entirely of glass (compare Fig. II, 10, 4 and Fig. II, 10, 2) will be found satisfactory provided the glass loop is not too large. 

For all point, axial rotation, and full rotation group symmetries, this observation holds if the orbitals are equivalent, certain space-spin symmetry combinations will vanish due to antisymmetry if the orbitals are not equivalent, all space-spin symmetry combinations consistent with the content of the direct product analysis are possible. In either case, one must proceed through the construction of determinental wavefunctions as outlined above. 

A turbine flowmeter consists of a straight flow tube containing a turbine which is free to rotate on a shaft supported by one or more bearings and located on the centerline of the tube. Means are provided for magnetic detection of the rotational speed, which is proportional to the volumetric flow rate. Its use is generally restric ted to clean, noncorrosive fluids. Additional information on construction, operation, range, and accuracy can be obtained from Holzbock (Instruments for Measurement and Control, 2d ed., Reinhold, New York, 1962, pp. 155-162). For performance characteristics of these meters with liquids, see Shafer,y. Basic Eng., 84,471-485 (December 1962) or May, Chem. Eng., 78(5), 105-108 (1971) and for the effect of density and Reynolds number when used in gas flowmetering, see Lee and Evans, y. Basic Eng., 82, 1043-1057 (December 1965). 

These devices are replacing the older tank and spiral-conveyor devices. Better provisions for speed and ease of fill and discharge (without powered rotation) minimize downtime to make this batch-operated device attractive. Heat-transfer coefficients ranging from 28 to 200 W/(m °C) [5 to 35 Btu/(h fF °F)] are obtained. However, if caking on the heat-transfer walls is serious, then values may drop to 5.5 or 11 W/(m °C) [1 or 2 Btu/(h fH °F)], constituting a misapplication. The double cone is available in a fairly wide range of sizes and construction materials. The users are the fine-chemical, pharmaceutical, and biological-preparation industries. 

As a general nile, the direct-heat units are the simplest and most economical in construction and are emploved when direct contact between the solids and flue gases or air can be tolerated. Because the total heat load must be introduced or removed in the gas stream, large gas volumes and high gas velocities are usually required. The latter will be rarely less than 0.5 m/s in an economical design. Therefore, employment of direct rotating equipment with solids containing extremely fine particles is likely to result in excessive entrainment losses in the exit-gas stream. 

Rotating equipment, except brick-hned vessels, operated above ambient temperatures is usually insulated to reduce heat losses. Exceptions are direct-heat units of bare metal construction operating at high temperatures, on which heat losses from the shell are neces-saiy to prevent overheating of the metal. Insulation is particularly necessary on cocurrent direct-heat units. It is not unusual for product cooling or condensation on the shell to occur in the last 10 to 50 percent of the cylinder length if it is not well insulated. 

The distinguishing feature of this dryer is the bottom-screw drive, as opposed to a top-drive unit, thus ehminating any mechanical drive components inside the vessel. The bottom-driven screw rotates about its own axis (speeds up to 100 rpm) and around the interior of the vessel (speeds up to 0.4 rpm). The screw is cantilevered in the vessel and requires no additional support (even in vessel sizes up to 20 m operating volume). The dryer is available in a variety of materials of construction, including SS 304 and 316, as well as Hastelloy. 

Construction is similar to that of other drum filters, except that vacuum is applied to the entire rotation. Before feeding slurry a precoat layer of filter aid or other suitable solids, 75 to 125 mm (3 to 5 in) thick, is apphed. The feed slurry is introduced and trapped in the outer surface of the precoat, where it is removed by a progressively advancing doctor knife which trims a thin layer of solids plus precoat (Fig. 18-126). The blade advances 0.05 to 0.2 mm (0.002 to 0.008 in) per revolution of the drum. When the precoat has been cut to a predefined minimum thickness, the filter is taken out of service, was ned, and freshly precoated. This turnaround time may be 1 to 3 h. 

Rotating electrical machines. Classification of types of constructions and mounting arrangements 2253/1974 BS EN 60034-7/1993 ... 

NEMA/MG-1/1993 NEMA/MG-2/1989 Motor and generators ratings, construction, testing and performance Safety Standards (enclosures) for construction and guide for selection, installation and use of rotating machines ... 

Safety Standards (enclosures) for construction and guide for selection, installation and use of rotating machines... 

Another generalization uses referential (material) symmetric Piola-Kirchhoff stress and Green strain tensors in place of the stress and strain tensors used in the small deformation theory. These tensors have components relative to a fixed reference configuration, and the theory of Section 5.2 carries over intact when small deformation quantities are replaced by their referential counterparts. The referential formulation has the advantage that tensor components do not change with relative rotation between the coordinate frame and the material, and it is relatively easy to construct specific constitutive functions for specific materials, even when they are anisotropic. 

The referential formulation is translated into an equivalent current spatial description in terms of the Cauchy stress tensor and Almansi strain tensor, which have components relative to the current spatial configuration. The spatial constitutive equations take a form similar to the referential equations, but the moduli and elastic limit functions depend on the deformation, showing effects that have misleadingly been called strain-induced hardening and anisotropy. Since the components of spatial tensors change with relative rigid rotation between the coordinate frame and the material, it is relatively difficult to construct specific constitutive functions to represent particular materials. 

---