Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Processing methods compression molding

Compression molding is an example of a simple process which does not require expensive equipment but produces cheaply and in simple shapes. Unlike most other processing methods, compression molding does make materials inexpensive through the use of large quantities of fillers. Compression molding applies unidirectional forces usually perpendicular to the material s surface which may thus affect filler orientation. [Pg.752]

Typical processing methods - compression molding, extrusion. Injection molding ... [Pg.41]

Typical processing methods compression molding, electrostatic powder coating, fluidized bed coating, film/tube extrusion, flame and plasma spraying, injection molding monofilament extrusion, wire cable injection molding ... [Pg.108]

Typical processing methods " compression molding, electrospinning, extrusion, extrusion blow molding, injection molding, photolithography, thermoforming ... [Pg.584]

Important processing methods injection molding, extrusion, blow molding, compression molding, thermoforming, casting... [Pg.645]

Typical processing methods bulk molding, casting, compression molding, encapsulation, injection molding, printed circuit board, pultrusion, resin transfer molding, sheet molding ... [Pg.701]

Eoamable compositions in which the pressure within the cells is increased relative to that of the surroundings have generally been called expandable formulations. Both chemical and physical processes are used to stabilize plastic foams from expandable formulations. There is no single name for the group of cellular plastics produced by the decompression processes. The various operations used to make cellular plastics by this principle are extmsion, injection mol ding, and compression molding. Either physical or chemical methods may be used to stabilize products of the decompression process. [Pg.404]

A knowledge of processing methods will be useful to the designer to help determine what tolerances can be obtained. With such high-pressure methods as injection and compression molding of 2,000 to 30,000 psi... [Pg.170]

CM is the most common method of molding TSs. In this process, material is compressed into the desired shape using a press containing usually a two-part closed mold and is cured with heat and pressure. This process is not generally used with TPs. TM, also called compression-transfer molding is a... [Pg.527]

The release of steroids such as progesterone from films of PCL and its copolymers with lactic acid has been shown to be rapid (Fig. 10) and to exhibit the expected (time)l/2 kinetics when corrected for the contribution of an aqueous boundary layer (68). The kinetics were consistent with phase separation of the steroid in the polymer and a Fickian diffusion process. The release rates, reflecting the permeability coefficient, depended on the method of film preparation and were greater with compression molded films than solution cast films. In vivo release rates from films implanted in rabbits was very rapid, being essentially identical to the rate of excretion of a bolus injection of progesterone, i. e., the rate of excretion rather than the rate of release from the polymer was rate determining. [Pg.88]


See other pages where Processing methods compression molding is mentioned: [Pg.439]    [Pg.26]    [Pg.262]    [Pg.265]    [Pg.12]    [Pg.26]    [Pg.51]    [Pg.8535]    [Pg.673]    [Pg.145]    [Pg.66]    [Pg.397]    [Pg.178]    [Pg.244]    [Pg.244]    [Pg.340]    [Pg.205]    [Pg.136]    [Pg.9]    [Pg.512]    [Pg.529]    [Pg.605]    [Pg.615]    [Pg.27]    [Pg.204]    [Pg.176]   


SEARCH



Compression molding

Compression molding process

Method process

Molding methods

Molding processes

Process compression

Processed method

Processing compression

Processing compression molding

Processing methods

Processing molding

Processing molding methods

© 2024 chempedia.info