Pressure swing

Steps. A pressure-swing cycle has at least three steps adsorption, blowdown, and repressurization. Although not always necessary, a purge step is normally used. In finely tuned processes, cocurrent depressurization and pressure-equalization steps are frequendy added. 

Relatively new methods for separating helium from natural gas use pressure swing adsorption (PSA) processes to recover helium at better than 99.99% purity. This type of process is probably less costiy for the production of gaseous helium but might be uneconomical for liquefied helium production. The PSA process is widely used to produce specification pure helium from 85+% cmde helium in conjunction with cryogenic enrichment of the ca 50% helium raffinate. 

As an alternative to scmbbing out the CO2 followed by methanation, the shifted gas can be purified by pressure-swing adsorption (PSA) when high purity hydrogen is desirable. 

Fig. 2. Hydrogen production flow sheet showing steam reforming, shift, and pressure swing adsorption (PSA). BFW = boiling feed water.

The second CO2 removal is conducted using the same solvent employed in the first step. This allows a common regeneration stripper to be used for the two absorbers. The gases leaving the second absorption step stiU contain some 0.25—0.4% CO and 0.01—0.1% CO2 and so must be methanated as discussed earlier. The CO, CO2, and possibly small amounts of CH, N2, and Ar can also be removed by pressure-swing adsorption if desired. 

Fig. 4. Coal gasification process. PSA = pressure-swing adsorption.

The impurities usually found in raw hydrogen are CO2, CO, N2, H2O, CH, and higher hydrocarbons. Removal of these impurities by shift catalysis, H2S and CO2 removal, and the pressure-swing adsorption (PSA) process have been described (vide supra). Traces of oxygen in electrolytic hydrogen are usually removed on a palladium or platinum catalyst at room temperature. 

H. A. Stewart and J. L. Heck, Hydrogen Purification By Pressure Swing Adsorption, Union Carbide Corp., Linde Division, New York. 

Regenerative adsorption units can be operated by a thermal-swing cycle, pressure-swing cycle, displacement-purge cycle, or inert-purge cycle. Combinations of these are frequently employed. 

Fig. 3. Pressure swing adsorption nitrogen generation system. CMS = carbon molecular sieve.

Pressure Swing Adsorption. Carbon dioxide can be removed by pressure adsorption on molecular sieves. However, the molecular sieves are not selective to CO2, and the gases must be further processed to achieve the high purity required for "over the fence" use as in the urea process. Use of pressure swing adsorption for CO2 removal appears most appHcable to small, stand-alone plants (29). 

Pressure Swing Adsorption. A number of processes based on Pressure Swing Adsorption (PSA) technology have been used in the production of carbon dioxide. In one version of the PSA process, CO2 is separated from CH using a multibed adsorption process (41). In this process both CH4 and CO2 are produced. The process requires the use of five adsorber vessels. Processes of this type can be used for producing CO2 from natural gas weUs, landfiU gas, or from oil weUs undergoing CO2 flooding for enhanced oil recovery (see Adsorption, gas separation). 

Adsorption Processes. More recendy, pressure swing adsorption (PSA) processes utilizing a high selectivity copper adsorbent have been utilized to effectively separate carbon monoxide from blast furnace gas and coke oven gas (97—101). 

Hydrogen Liquefaction. Hydrogen can be produced from caustic—chlorine electrolytic cells, by decomposition of ammonia or methanol, or by steam—methane reforming. Hydrogen recovered by these methods must be further purified prior to Hquefaction. This is generally achieved by utilizing pressure swing adsorption methods whereby impurities are adsorbed on a soHd adsorbent. 

Fig. 11. Schematic illustration of the thermal-swing and pressure-swing cycles. In thermal swing, the differential loading, Av, is given by — x at...

---